ar7240w2000a

Removing, installing outer pushbutton of folding door

Type ar · topic 72.40 · version 0102 · 2012-02-23

Applies to: MODEL 957 with BODY 957.810

Where it sits

Function group 3 Body › 72 Doors › 72.40 Door control — Series 957

EinPAS 35 Body/frame/detachable parts › 35.35 Door › 35.35.30 Door drive system/door control — Series 957

EinPAS 35 Body/frame/detachable parts › 35.51 Passenger door 1 › 35.51.31 Door drive system/door control — Series 957

EinPAS 35 Body/frame/detachable parts › 35.52 Passenger door 2 › 35.52.31 Door drive system/door control — Series 957

EinPAS 35 Body/frame/detachable parts › 35.53 Passenger door 3 › 35.53.31 Door drive system/door control — Series 957

EinPAS 35 Body/frame/detachable parts › 35.54 Passenger door 4 › 35.54.31 Door drive system/door control — Series 957

AR72.40-W-2000A

Removing, installing outer pushbutton of folding door

21.2.12

MODEL 957 with BODY 957.810

Removing, installing outer pushbutton of folding door

W72.40-0001-06

1 Side wall trim, bottom

2 Lower B-pillar trim

3 Side wall trim, top

4 Seat belt guide bracket

5 Screw

6 Contact housing

7 Counter-holder

8 Screws

9 Spacer

10 Sealing ring

11 Pushbutton housing

Removing, installing

Danger!

Risk of explosion caused by escaping oxyhydrogen gas. Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries caused by short circuit. Risk of poisoning caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices

No fire, sparks, open flames or smoking.

Wear acid-resistant gloves and clothing and safety glasses with side guards.

Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground.

Only fill liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers.

AS54.10-Z-0001-01A

1

Disconnect battery ground cable

Ensure that no accidental contact can be made between ground cable and negative pole of battery.

Notes on battery

All models

AH54.10-P-0001-01A

2

Remove front passenger seat bench

3

Remove lower B-pillar trim (2)

Installation: Push B-pillar trim firmly until Velcro fastening locks.

4

Remove seat belt guide bracket (4) on C-pillar

*BA91.40-N-1001-01F

5

Remove lower side wall trim (1)

Detach upper side wall trim (3) in lower area.

6

Disconnect contact housing (6) from counter-holder (7)

7

Loosen screws (8) in counter-holder (7) by turning three or four times

Installation: Carefully tighten screws

8

Remove counter-holder (7) and spacer (9)

Unlock bayonet seal by turning counter-holder anti-clockwise.

9

Remove pushbutton housing (11)

Installation: Replace sealing ring (10)

10

Installation takes place in reverse order

11

Carry out function check of folding door

12

Adjust time on tachograph

Seat belt/emergency tensioning retractor

Number

Designation

Body 957.810 in model 957

BA91.40-N-1001-01F

Screw, seat belt guide bracket on C-pillar

7/16 ŰNF

Nm

40

Referenced documents