Remove/install exterior sliding door emergency release

AR72.40-D-1008A

Remove/install exterior sliding door emergency release

05.12.2019

Model

906.657

with code P0E (Sprinter Tourer master code)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code P0F (Master code for Sprinter Tourer 19+1 Inland)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code P0G (Master code Sprinter Tourer 16+1)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code P0H (Master code Sprinter Tourer 19+1)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code PE4 (DCAA bus master code, Argen)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code PE5 (Mastercode, bus seats on raised base, Argen)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

1

Sliding door emergency release

2

Bolts

3

Safety sticker

1

Sliding door emergency release

5

Screw

8

Switches

2

Bolts

6

Cable

9

Screw

4

Electrical connectors

7

Bracket

10

Screw

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

 Caution

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.

AS00.00-Z-0017-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 

Remove/install

1

Unlock sliding door emergency release (1) with key

2

Carefully loosen safety sticker (3) on sliding door emergency release (1) and remove

 Installation: Check adhesive points on safety sticker (3).

If adhesive points on safety sticker (3) are damaged or soiled.



Install new safety sticker (3).

3

Remove lower sliding door paneling

MODEL 906.657 except CODE ZO1 (James Cook Compact camper) except CODE ZO2 (James Cook Classic camper)

AR72.16-D-6610G

4

Remove switch (8)

 To do this, unscrew bolts on switch (8) while holding nuts steady and remove switch (8).

5

Remove screw (5)

AR72.16-D-2214A

 To do this, hold clamp steady.

 Installation: Adjust control cable (6) of sliding door emergency release (1).

6

Remove pull wire of control cable (6) from clamp

 Installation: Check pull wire of control cable (6) for damage.

Depending on findings



Install new pull wire of control cable (6) in place of damaged pull wire.

Route cables for closing system

AR72.16-D-2210-02A

7

Unscrew bolts (9, 10) and place bracket (7) with control cable (6) to one side

 Installation: Align bolts (9, 10) and tighten beginning with bolt (10).

8

Disconnect electrical connections (4)

9

Open sliding door

 Open sliding door until bolts (2) and nuts on sliding door emergency release (1) are accessible.

10

Unscrew nuts from bolts (2)

 To do this, hold bolts (2) steady from outside and then remove.

11

Remove sliding door emergency release (1)

 Installation: Observe sliding door emergency release installation position (1). The switch for the electrical connections (4) must point upward.

12

Remove seal on sliding door emergency release (1)

 Installation:
Inspect gasket for damage.

Depending on findings



Replace damaged seal with new one.

13

Install in the reverse order

Learn in electric sliding door

14

Close sliding door with switch on center console, open completely, and close again



Check

15

Perform function test