Model | 906.657 |
with code P0E (Sprinter Tourer master code) | |
with code T16 (Sliding door right) | |
with code T55 (Electric operation of sliding door on right) | |
Model | 906.657 |
with code P0F (Master code for Sprinter Tourer 19+1 Inland) | |
with code T16 (Sliding door right) | |
with code T55 (Electric operation of sliding door on right) | |
Model | 906.657 |
with code P0G (Master code Sprinter Tourer 16+1) | |
with code T16 (Sliding door right) | |
with code T55 (Electric operation of sliding door on right) | |
Model | 906.657 |
with code P0H (Master code Sprinter Tourer 19+1) | |
with code T16 (Sliding door right) | |
with code T55 (Electric operation of sliding door on right) | |
Model | 906.657 |
with code PE4 (DCAA bus master code, Argen) | |
with code T16 (Sliding door right) | |
with code T55 (Electric operation of sliding door on right) | |
Model | 906.657 |
with code PE5 (Mastercode, bus seats on raised base, Argen) | |
with code T16 (Sliding door right) | |
with code T55 (Electric operation of sliding door on right) |
D72.29-1121-09
1 | Rocker | 5 | Electrical connector | 9 | Shaft | ||
2 | Bracket | 6 | Electrical connector | 10 | Assembly funnel | ||
3 | Cable | 7 | Bolts | M73/1 | Right electric sliding door drive | ||
4 | Cable tie | 8 | Shaft retainers | N69/6 | Right sliding door control unit |
18 | Emergency release lever |
D72.16-1352-11
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
| Remove/install | ||
1 | Remove bottom door trim |
| |
2 | Release emergency release lever (18) | To do this, turn emergency release lever (18) clockwise. | |
Installation: Turn emergency release lever (18) counterclockwise to horizontal position. | |||
3 | Remove all cable ties (4) | Installation: Insert new cable ties (4) everywhere. | |
4 | Remove control cable (3) from rocker (1) | To do this, press rocker (1) upward. | |
5 | Remove cable (3) | To do this, pull control cable (3) out of bracket (2). | |
6 | Disconnect electrical connection (5) at STR control unit (N69/6) | ||
7 | Disconnect electrical connector (6) | ||
8 | Remove bolts (7) | ||
9 | Remove shaft (9) | To do this, press shaft retainers (8) outward in direction of arrow and simultaneously remove right electric sliding door drive (M73/1) from shaft (9). | |
Installation: Install shaft (9) in assembly funnel (10) on right electric sliding door drive (M73/1) and press in until shaft retainers (8) arrest. | |||
10 | Remove right electric sliding door drive (M73/1) | ||
11 | Install in the reverse order | ||
Learn in electric sliding door | |||
12 | Completely open sliding door with switch on center console and close again | ||
| Check | ||
13 | Carry out function check |
Referenced documents
- ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
- ar7216d6610g Remove/install door panel of sliding door
- as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.
- as0000z001701a Risk of injury caused by scraping or cutting body parts on sharp vehicle parts