Remove/install side paneling in rear

AR68.30-P-4780EC

Remove/install side paneling in rear

30.03.2016

Model

204.3, 207.3/4

Upper side paneling

Modification notes

24.02.2016

Method concerning removal of rear tweeter adapted.

Model 207.4

1

Upper side paneling

16

Seat backrest

17

Cover

18

Rear seat belt

19

Cover

20

Screw

Illustrated on model 207.3

1

Upper side paneling

4

Belt end fitting

7

Belt extender eye (model 207.3/4)

2

Bottom side paneling

5

Bolts

8

Catch hook (model 207.3/4.)

3

Edge guard

6

Front seat belt

9

Lock

Model 207.4

1

Upper side paneling

21

Cover

22

Bolts

23

Draft stop mount

Illustrated on model 207.3

1

Upper side paneling

12

Clips

24

Rear tweeter

2

Bottom side paneling

13

Electrical connection (Model 207.3/4)

25

Rear power window switch (model 207.3/4)

10

Clip

14

Speaker grille

11

Clips

15

Belt extender (model 207.3/4)



Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

 

Remove/install

1.1

Move left or right rear side window completely down

Model 207.3Upper side paneling

1.2

Partially open soft top

Model 207.4Upper side paneling

 Leave soft top compartment lid positioned upright.

2

Switch off ignition and store transmitter key outside of transmission range (min. 2 m)

3

Unclip cover (17) from cover (19) starting at rear seat backrest (16) (arrow B)

Model 207.4Upper side paneling

 Installation: Ensure that panel (17) is seated correctly in (19)..

4

Slide cover (17) downward along rear seat belt (18)

Model 207.4Upper side paneling

5

Remove bolt (20)

Model 207.4Upper side paneling

6

Unclip cover (19) above and remove upward

Model 207.4Upper side paneling

 Installation: Ensure that cover (19) is seated correctly below upper side paneling (1).

7

Remove edge guard (3) in area of upper side paneling (1) and pull to side

8

Unclip cover (21)

Model 207.4Upper side paneling

9

Unscrew bolts (22) from draft stop mount (23)

Model 207.4Upper side paneling

10

Unscrew bolts (5) and remove belt end fitting (4)

 Installation:
Do not install seatbelt (6) when twisted.
Other proper operation cannot be ensured.

 Bolt at front belt end fitting

*BA91.40-P-1003-01P

11

Pull seat belt extender eye (7) out of upper side paneling (1) until catch hook (8) is accessible

Model 207.3/4Upper side paneling

12

Unlock seat belt extender eye (7) by pressing catch hook (8) and remove from seat belt extender (15)

Model 207.3/4Upper side paneling

13

Completely retract seat belt extender (15) by hand

Model 207.3/4Upper side paneling

14

Open lock (9) by pulling in direction of arrow (A)

 Extraction hook

*140589023300

15

Remove clamp (10)

16

Unclip upper side paneling (1) in area of clips (11, 12)

 Long wedge

*115589035900

17

Disconnect electrical connector from rear tweeter (24)

18

Disconnect electrical connector (13) from rear power window switch (25)

Model 207.3/4Upper side paneling

19

Unclip upper side paneling (1) from lower side paneling (2)

20

Remove front seatbelt (6) and upper side paneling (1)

21

Unclip speaker grille (14) with rear tweeter (24) at bottom, pivot upward and remove

When replacing upper side paneling (1)

22

Install in the reverse order

 Seat belts/emergency tensioning retractors

Number

Designation

Model 204.3

Model 207

BA91.40-P-1003-01P

Bolt at front belt end fitting

Nm

35

35