ar6830d3520ts

Remove/install rear entrance cover

Type ar · topic 68.30 · version 0100 · 2019-01-04

Applies to: Model 907.6/7, 910.6

Where it sits

Function group 3 Body › 68 Interior equipment › 68.30 Coverings, trim — Series 907 (models 6**, 7**) · Series 910 (models 6**)

EinPAS 37 Interior equipment › 37.45 Trim › 37.45.37 Footwell trim — Series 907 (models 6**, 7**) · Series 910 (models 6**)

AR68.30-D-3520TS

Remove/install rear entrance cover

20.12.2018

Model

907.6/7, 910.6

Remove/install rear entrance cover

D68.30-A001-79

Shown on model 907.6 with code W73 (Rear-end door step) except code V36 (Roof lining)

1	Cover		5	Bolts
2	Caps		6	Guide pin
3	Bolts		7	Locking elements
4	Lock striker

Topical note	Notes on carrying out repair work in the vehicle interior		AH68.00-N-0001-01S
 	Remove/install
1	Fully open rear-end doors.
2	Unclip covers (2).	 Clip remover	*452589016300
3	Remove screws (3) and remove lock striker (4).	 Installation: Only tighten screws (3) after adjusting the locking system of the rear-end doors.
4	Remove screws (5) and remove guide pin (6).	 Installation: Only tighten screws (5) after adjusting the locking system of the rear-end doors with the specified torque.
5	Remove locking elements (7) with a suitable screwdriver.	 Carefully remove locking elements (7) and use a suitable base. Otherwise, damage can occur to the cover (1).
6	Unclip cover (1) from body and remove.	 Model 907.6/7 with code V08 (Range of parts, roof lining for bodybuilders) Model 907.6/7 with code V36 (Panelling under roof) Installation: Ensure that the cover (1) is seated correctly under the D-pillar trims.
		 WIS Service Media wsm://04_201800_37
		 Installation: Ensure that catch hooks of cover (1) are inserted into the body correctly.
		 Clip remover	*452589016300
7	Install in the reverse order
 Warning	Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
8	Adjust locking system of rear-end doors.		AR72.20-D-1032-07TS
		 Screw, guide pin to body	*BA72.20-N-1006-01TS
		 Screw/bolt, lock striker to body	*BA72.20-N-1005-01TS

 Rear-end door

Number	Designation			Model 907.6/7, 910.6
BA72.20-N-1005-01TS	Screw/bolt, lock striker to body	M6	Nm	13
		M8	Nm	20

 Rear-end door

Number	Designation		Model 907.6/7, 910.6
BA72.20-N-1006-01TS	Screw, guide pin to body	Nm	20

Remove/install rear entrance cover

452 589 01 63 00

Clip remover

Referenced documents

ah6800n000101s Notes on carrying out repair work in the vehicle interior
ar7220d103207ts Adjust closing system on rear-end door
as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.