ar6310p067006lwe

Install outer rear wheel well

Type ar · topic 63.10 · version 0101 · 2019-06-19

Applies to: Model 213

Where it sits

Function group 3 Body › 63 Side wall › 63.10 Side wall — Series 213

EinPAS 35 Body/frame/detachable parts › 35.34 Sidewall › 35.34.41 Carrier/wheel well — Series 213

AR63.10-P-0670-06LWE

Install outer rear wheel well

Model

213

Check values for gap dimensions

Number

Designation

Model 213.0/1

Model 213.2

BE60.00-P-1009-01GA

Rear door to side section, bottom

Dimension "I"

mm

3,3 (0,5)

3,3 (0,5)

For picture, see

AR60.00-P-0700-01LWE

AR60.00-P-0700-01LWE

Check values for gap dimensions

Number

Designation

Model 213.0/1

Model 213.2

BE60.00-P-1011-01GA

Trunk lid to fender at rear, top

Dimension "K"

mm

3,3 (0,8)

-

For picture, see

AR60.00-P-0700-01LWE

-

Check values for gap dimensions

Number

Designation

Model 213.0/1

Model 213.2

BE60.00-P-1014-01GA

Rear sidewall to taillamp

Dimension "N"

mm

1 (0,7)

1 (0,7)

For picture, see

AR60.00-P-0700-01LWE

AR60.00-P-0700-01LWE

Check values for gap dimensions

Number

Designation

Model 213.0/1

Model 213.2

BE60.00-P-1015-01GA

Fuel filler flap

Dimension "O"

mm

2 (0,5)

2 (0,5)

For picture, see

AR60.00-P-0700-01LWE

AR60.00-P-0700-01LWE

Repair materials

Number

Designation

Order number

BR00.45-Z-1035-13A

Blind rivet 6.412 (clamping range 1 mm to 3.5 mm, draw-off strength min. 15.5 kN)

A 000 991 76 32

BR00.45-Z-1056-07A

1K-zinc dust paint

A 000 986 28 00

The next steps are shown on the left side of the vehicle and must be performed in the same way in the event of damage on the right side of the vehicle.
Further information can be found in the superordinate service document.
The safety information in the superordinate service document must be observed.

Install outer rear wheel well

Shown on the right side of the vehicle of model 213.0

P63.10-A060-12

Install outer rear wheel well

1

Install outer rear wheel well (1), rear fender, rear lamp, seal of the trunk lid, trunk lid, and lock striker and fit.



2

Check gaps and adjust       .



3

Fix outer rear wheel well (1) in place.



4

Remove rear fender, rear lamp, seal of the trunk lid, trunk lid, and lock striker.



5

Drill rivet holes on outer rear wheel well (1) with Ø 6.7 mm bit (area A).



6

Remove outer rear wheel well (1).



7

Deburr rivet holes on outer rear wheel well (1) and body on both sides.



8

Remove drilling chips.



9

Coat insides of riveted joints with zinc dust paint .


Shown on the left side of the vehicle of model 213.0

P63.10-5499-12

Install outer rear wheel well

Shown on the right side of the vehicle of model 213.0

P63.10-A061-12

Install outer rear wheel well

10

Install outer rear wheel well (1) and fix in place.



11

Rivet outer rear wheel well (1) with rivets with a diameter of 6.4 x 12 (area B).


Clamping range 1.2 mm.


Shown on the left side of the vehicle of model 213.0

P63.10-5501-12

Install outer rear wheel well

P63.10-A062-08

Shown on the right side of the vehicle of model 213.0

Install outer rear wheel well

P63.10-5502-08

Shown on the left side of the vehicle of model 213.0

12

Outer rear wheel well (1) (areas C).

13

Outer rear wheel well (1) (area D).