P60.10-0001-09
P60.10-0044-09
Straightening set, entire scope 7202.300
1, 2 Carrier for mounts 3 and 4
3, 4 Mounts for front cross member for carrier 1, 2
5, 6 Carrier for folding mount 7 and 8
7, 8 Folding mount for carrier 5 and 6
9 Connector for folding mount 7 and 8
10, 11 Mounts for front wishbone consoles
12 Check and locating plug for wishbone console mounts 10/11
13 Mount for locating pin of locating hole (FV) in front axle cross member
14 Locating pin for mount 13
15, 16 Base support for mounts 17/18 and 20/21
17, 18 Mounts for spring support for base carrier 15/16
19 Check and locating plate for mount 17/18
20, 21 Mounts for upper wishbone bearing to base carrier 15/16
22 Check and locating plug for mount 20/21
23 Mount for steering mount
24 Mounting plug for mount 23
25 Locating plug for mount 23
26 Mount for steering idler arm bearing
27 Control plug for mount 26
28, 29 Mounts for rear wishbone consoles
30, 31 Mounts for front outer longitudinal member
32, 33 Base carrier for mount 34 and 35
34, 35 Mounts for base carrier 32 and 33
36, 37 Spacer blocks for mount 34 and 35
38 Locating pin for mount 39
39 Mount for locating pin 38 for checking locating hole (K)
40 Mount for drive shaft bearing console for base part
MZ 080
41, 42 Base part for front rear axle mounting point
43 Cylindrical mount for base part 41/42
44 Centering sleeve for base part 41, 42 and cylindrical mount 43
45 Screw M12x1.5x150 for base part 41/42, cylindrical mount 43 and centering sleeve 44
46, 47 Mount for rear outer longitudinal member
48, 49 Base part for rear rear axle mounting point
50 Cylindrical mount for base part 48 and 49
51 Centering sleeve for base part 48/49 and cylindrical mount 50
52 Screw M12x1.5x110 for base part 48/49, cylindrical mount 50 and centering sleeve 51
53 Mounting block for rear rear axle mounting point for base part 48/49 and centering sleeve 51
54 Clamping tool for base part 48 and 49
55 Screw for clamping tool 54
56, 57 Mount for rear bumper mounting point
58 Check and locating plug for mount 56 and 57 (for model 208.4 shorten knurled section)
59, 60 Base carrier for mount 61 and 62
61, 62 Mount for rear cross member and rear center section to base carrier 59 and 60
63 Assembly strip for base carrier 59 and 60
64 Collar bolt for rear cross member and rear center section
65 Spacer for collar bolt 64
67 Plate for clamping tool screw 55
Pay attention to the arrangement drawings enclosed with the straightening tool set.
The positions illustrated in the figures are given in the set-up plans.
P60.10-0205-06
Trunk straightening tool hardware
19 2 each check and locating plate for mount 17/18
24 2 each mounting plug for mount 23
25 1 each locating plug for mount 23
36 1 each spacer block for mount 34
37 1 each spacer block for mount 35
45 2 each. screws M12x1.5x150 for front rear axle mount
52 2 each screws M12x1.5x110 rear rear axle mount
64 2 each collar bolt for rear cross member and rear center section
65 2 each spacer for collar bolt 64
2 each washer for collar bolt 64
6 each screws for mount 20/21 and base part 15/16
6 each screws for mount 20/21 and base part 15/16
6 each nut M12 for screws 955.750
14 each screws M12x25
2 each screws M8x25
2 each screws M8x25
4 each nut M8
2 each screws M12x16
P60.10-0208-06
Shorten check and locating plug (58) approx. 50 mm on knurled side for model 208.4
Trunk straightening tool hardware
12 2 each check and locating plug for front wishbone bearing console mount 10/11
14 1 each locating pin for mount 13
22 2 each check and locating plug for mount 20/21
27 1 each locating pin for mount 26
38 1 each locating pin for mount 39
43 2 each cylindrical mount for front rear axle mounting point
44 2 each centering sleeve for base part 41/42
50 2 each cylindrical mount for rear rear axle mounting point for mount 56/57
51 2 each centering sleeve for base part 48/49
53 2 each mounting block for rear rear axle mounting point for base part 48/49
54 2 each clamping tool for base part 48/49
55 2 each screw for clamping tool 54
58 2 each check and locating plug for shock absorber mount 56/57
(for model 208.4 shorten knurled section)
66 2 each check and locating plug for rear wishbone bearing console mount 28/29
67 2 each washer for screw 55
Pay attention to the arrangement drawings enclosed with the straightening angle set.
The positions not illustrated in the figures are given in the set-up plans.
Fig. item etc. | Work instructions | ||
| Observe set-up plans included with straightening set. | ||
| Set up Celette straightening bracket set | Model 202.026/029/033/086/089/093 and Model 208.365/370/ 465/470 Also use supplementary straightening set for engines 112, 113! See | |
Models 202, 208 with engines 112, 113 Celette supplemental straightening bracket set | |||
Model 208 Celette supplemental straightening bracket set | |||
Celette straightening bracket set | |||
models 208.4 Use additional supplementary straightening set on model | |||
models 208.4 Celette supplemental straightening bracket set | |||
Tensioning chain on mount for longitudinal member |
Celette straightening set 7202.300
Number | Designation | models 202.0/1 | models 208.3/4 | |
BA60.10-P-1001-01A | Tensioning chain on mount for longitudinal member | Nm | 50 | 50 |
Commercially available tools
Number | Designation | |
WH58.30-Z-1007-06A | Reversible ratchet | |
WH58.30-Z-1026-06A | Screwdriver bit, 8 mm for hexagon socket head screws | |
WH58.30-Z-1002-11A | Double end box wrench, offset, 22 x 24 mm |
Workshop equipment
WE58.40-Z-1006-01A | Celette straightening bracket set 7208.309 (model C 208), as supplement to 7202.300 (model 202) |
WE58.40-Z-1012-01A | Celette straightening bracket set 7202.309 (model 202, 208 with engine 112, 113), as supplement to 7202.300 (model 202) |
WE58.40-Z-1015-01A | Celette straightening bracket set 7208.308 (model A 208), as supplement to 7202.300 (model 202), as well as 7208.309 (model C 208) |
WE58.40-Z-1001-01E | Celette straightening bench |
WE58.40-Z-1007-01E | Celette module crossmember set 955.940 |
WE58.40-Z-1008-01E | Celette additional member 955.908 |
WE58.40-Z-1009-01E | Celette straightening bracket set 7202.300 |
WE58.40-Z-1008-03A | Pneumatic ratchet |
Referenced documents
- ar6010p110001a Setting up Celette straightening tools