Model | 461 |
with code I94 (265/70 R17.5 Street Terrain tyres) | |
with code I95 (265/70 R17.5 Mud Terrain tyres) | |
with code R86 (Spare wheel including run-flat system) | |
with code RF3 (Wheels 7.5Jx17,5") | |
except code 979 (Special protection MB Guard) | |
except code R91 (Omission of spare wheel/spare rim) | |
except code RY3 (Run-flat system) |
P40.10-7043-07
1 | Check for condition and proper seating of rivet nut inserts (8). |
In areas (A, B, C). |
2 | Assemble the three run-flat tire ring segments (7). |
3 | Install wedges (6). |
Only in areas (B, C). |
4 | Apply thread locking agent to thread of bolts (5) parts kit. |
5 | Install bolts (5) with retaining washers (3.2) and tighten bolts (5) finger-tight. |
Only in areas (B, C). |
Replace retaining washers (3.2). |
6 | Coat complete inside area (cross-hatched area) of run-flat tire ring (7) with high-temperature grease. |
7 | Guide cable (9) through the openings (arrows) on the run-flat tire ring (7). |
Weld in area (A) with . |
The cable (9) is required to draw together the run-flat tire ring segments (7). |
P40.10-7044-01
P40.10-7042-07
8 | Install run-flat tire ring (7). |
Check run-flat tire ring (7) is correctly seated. |
9 | Install spreader (1) in area (A). |
10 | Pry off tire sidewall from disk wheel. |
Weld in area (A) with . |
Pry off tire sidewall using spreader (1) only far enough to gain access to the threaded connection. |
11 | Use cable (9) to pull run-flat tire ring together. |
Weld in area (A) with . |
12 | Install wedge (6). |
Weld in area (A) with . |
13 | Apply coating of thread locking agent to thread of bolt (5). |
14 | Install bolt (5) with retaining washer (3.2). |
Only in area (A). |
Replace retaining washer (3.2). |
15 | Tighten bolt (5) to specified tightening torque . |
Only in area (A). |
16 | Apply coating of thread locking agent to thread of bolt (5). |
17 | Install bolt (2) with retaining washer (3.1) and lock washer (4). |
Only in area (A). |
Replace retaining washer (3.1). |
18 | Tighten bolt (2) to specified tightening torque. |
Only in area (A). |
19 | Remove cable (9). |
20 | Remove spreader (1) from area (A). |
21 | Install spreader (1) in area (B). |
The following operation steps, that are conducted in area (B), must be conducted afterwards in area (C) in the same sequence. |
22 | Tighten the bolt (5) to the specified tightening torque. |
Weld in area (B) with . |
23 | Apply coating of thread locking agent to thread of bolt (5). |
24 | Install bolt (2) with retaining washer (3.1) and lock washer (4). |
Weld in area (B) with . |
Replace retaining washer (3.1). |
25 | Tighten bolt (2) to specified tightening torque. |
Weld in area (B) with . |
26 | Remove spreader (1) from area (B). |
27 | Repeat the activities from the preceding operation steps from area (B), by observing all specifications in the same sequence in area (C). |