AR32.32-P-0505SL | Remove/install of wiring harness for adaptive damping system (ADS) | 25.7.03 |
MODEL 129
P32.32-2050-06
1l Cover
1r Cover
3r Connector
4d Connector
5 Bracket
6 Cable retainer
7 Cover
8 Cover
9 Ground connection
51k ADS wiring harness
N16/1 Base module (BM [GM])
N47 Traction systems control module
X11/3 Right diagnostic socket (9-pin)
X30/1 Multifunction block connector
P32.32-2051-06
2 Splash wall
3l Connector
10 Connector
11 Connector
36 Connector
37 Connector
51k ADS wiring harness
Y36 Level adjustment control valve
Y37 Level adjustment check valve
Y51x1 Damping valve unit connector
| Remove/Install | ||
Danger! | Risk of death. Death may result if vehicle slips or topples from the lifting platform. | Align vehicle between columns of lifting platform and position the four support plates below support points specified by vehicle manufacturer. | |
1 | Raise vehicle. | ||
2 | Remove engine compartment paneling | ||
Models 129.059 /064 /068 | |||
3 | Disconnect connector (36) from level control control valve (Y36) | The connector (36) is located on the distributor in the bottom right of the engine compartment. | |
4 | Disconnect connector (37) on level adjustment shutoff valve (Y37) | The connector (37) is located on the distributor in the bottom right of the engine compartment. | |
5 | Lower vehicle | ||
Danger! | Risk of injury to fingers being jammed or squeezed when removing and installing or aligning hoods, doors, trunk lid/tailgate or sliding roof. | When moving components, ensure that no body parts or limbs are within the operating range of moving parts. | |
6 | Open engine hood | ||
7 | Remove covers (1l, 1r) of the cable ducts in the engine compartment | ||
8 | Detach splash wall (2) | ||
9 | Disconnect connect on left damping valve unit (Y51x1) | ||
10 | Disconnect connector on right damping valve unit | ||
11 | Disconnect connectors (3l, 3r) of wheel sensors | ||
12 | Disconnect connector (4d) of ADS wiring harness (51k) on right diagnostic socket, 9-pin (X11/3) | Detach right diagnostic socket, 9-pin (X11/3). | |
13 | Detach bracket (5) of pneumatic valves | ||
14 | Remove traction system control module (N47) | ||
15 | Remove overvoltage protection relay | The relay is located in the right front control unit box. | |
16 | Detach wiper system relay | The relay is located in the left control module box. | |
17 | Remove cable duct (6) | ||
18 | Remove cover (7) and disconnect connections of control units voltage supply | Terminal 87 and terminal 61 | |
19 | Remove base module (GM) (N16/1) | ||
20 | Detach ground connection (9) | ||
21 | Disconnect connector of multifunction block (X30/1) | ||
22 | Remove cover (8) of cable duct to interior | ||
23 | Detach passenger-side cover under instrument panel | ||
24 | Disconnect connectors (10, 11) of ADS wiring harness (51k) in interior | ||
25 | Expose and remove ADS wiring harness (51k) | ||
26 | Install in the reverse order |
Referenced documents
- ar6120p1105ab Detach/attach lower engine compartment paneling
- as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
- as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.
- ra68001290150x 0150 - Removal and installation of the cover under the instrument panel A. Driver's side cover, B. Passenger's side cover Model 129