ar0707p1454a

Remove/install hot film mass air flow sensor together with air intake pipe

Type ar · topic 07.07 · version 0110 · 2002-10-30

Applies to: ENGINE 112.910 in MODEL 202.026 /086 ENGINE 112.920 in MODEL 202.029 /089 ENGINE 112.911 in MODEL 210.061/261 ENGINE 112.921 in MODEL 210.063 /263 /081 /281 /663 ENGINE 112.941 in MODEL 210.065 /082 /265 /282 ENGINE 112.940 in MODEL 208.365 /465 ENGINE 112.942 in MODEL 163.154 ENGINE 112.970 in MODEL 163.157 ENGINE 113.940 in MODEL 210.070 /270

Where it sits

Function group 1 Engine › 07 Mixture formation › 07.07 Air volume guage, air mass guage — Series 163 (models 154, 157) · Series 202 (models 026, 029, 086, 089) · Series 208 (models 365, 465) · Series 210 (models 061, 063, 065, 070, 081, 082, 261, 263, 265, 270, 281, 282, 663)

EinPAS 15 Engine › 15.30 Air intake/charging › 15.30.33 Intake manifold/charge air pipe — Series 163 (models 154, 157) · Series 202 (models 026, 029, 086, 089) · Series 208 (models 365, 465) · Series 210 (models 061, 063, 065, 070, 081, 082, 261, 263, 265, 270, 281, 282, 663)

EinPAS 15 Engine › 15.45 Engine management › 15.45.12 Sensor/switch/wiring harness — Series 163 (models 154, 157) · Series 202 (models 026, 029, 086, 089) · Series 208 (models 365, 465) · Series 210 (models 061, 063, 065, 070, 081, 082, 261, 263, 265, 270, 281, 282, 663)

Also applies to engines/gearboxes: 112 910, 112 911, 112 920, 112 921, 112 940, 112 941, 112 942, 112 970, 113 940

AR07.07-P-1454A

Remove/install hot film mass air flow sensor together with air intake pipe

1.10.96

ENGINE 112.910 in MODEL 202.026 /086

ENGINE 112.920 in MODEL 202.029 /089

ENGINE 112.911 in MODEL 210.061/261

ENGINE 112.921 in MODEL 210.063 /263 /081 /281 /663

ENGINE 112.941 in MODEL 210.065 /082 /265 /282

ENGINE 112.940 in MODEL 208.365 /465

ENGINE 112.942 in MODEL 163.154

ENGINE 112.970 in MODEL 163.157

ENGINE 113.940 in MODEL 210.070 /270

Remove/install hot film mass air flow sensor together with air intake pipe

P07.61-0440-06

Shown on Engine 112

1/2 Right crankcase vent line

2 Air cleaner

2/1 Resonance housing

2/2 Air intake tube

2/3 Bolt

B2/5 Hot film mass air flow sensor

Fig. item, etc.

Work instructions

Cable actuator of electronic accelerator

Removal: Before the air intake tube (2/2) is removed, detach cable (arrow)

Lock of air intake tube to actuator electronic accelerator

Removal: Press plate to bottom by means of screwdriver

1/2

Right crankcase vent line

Installation: Slip-on from below

2

Air filter

2/1

Resonance housing

Detach from above out of the rubber mounting

2/2

Air intake pipe

Bolt (2/3)

B2/5

Hot film MAF sensor

Unplug electrical connector.

Slacken hose clamp