Lift/jack up vehicle

AR00.60-D-1000H

Lift/jack up vehicle

09.12.2015

Model

900, 906

Picture no., etc.

Work notes

 Danger !

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Secure vehicle on vehicle lift

AR00.60-D-0100H


Laden vehicles, vehicles with a heavy body and vehicles with unfavorable load distribution must generally be secured.
Otherwise these may fall.

Vehicles with low frame

Model 906.132/134/136


The vehicle must not be lifted at longitudinal member at rear.
Otherwise the longitudinal member is damaged.

 Vehicles with low frames may only be lifted at the rear at the integral carrier (5) in the vicinity of the inner supports of the semi-trailing arms, unless the vehicle has a vehicle lift support point, which should then be used to lift the vehicle.

Vehicles for winter service operations

Model 906.153/253
with code CV1 (Pre-installation for winter service vehicle)


To lift at the front, support drifts (017) must be used and the vehicle can only be lifted when unloaded.
Otherwise the longitudinal member will be damaged and the vehicle can be tipped off of the vehicle lift (011).

Vehicles with electric step

Model 900, 906
with code T57 (Right load compartment sliding door electric step)
Model 900
with code T05 (Electric step, front passenger door)
Model 906
with code T58 (Left load compartment sliding door electric step)


When lifting, make sure that there is enough distance between the electric step and the support arms of the vehicle lift (011).
The electrical step may otherwise be damaged.

1

Front support to spring clamp plate

Model 900
Model 906
except code CV1 (Pre-installation for winter service vehicle)

 Can be used on any vehicle, provided that the front axle does not have to be removed.

2

Front support to longitudinal member

 Model 906.153/253
with code CV1 (Pre-installation for winter service vehicle)
Only perform front support at longitudinal member with the support drifts (017).

 Model 900.655/657
Model 906.135/136/235
with box body or special bodyModel 906.635/637/655/657/735
If possible, always support at front mount at longitudinal member (2).

 For work which requires the front axle to be removed.

3

Support at rear to front rear spring bracket

Model 906.11/131/133/135/21/23

4

Rear support at longitudinal member

Model 900.63, 906.61/63/71/73

 If possible, always support at rear mount at longitudinal member (4).

5

Frame-type integral support

Model 906.132/134/136

6

Mount on front rear spring bracket

Model 900, 906.15/25/6/7

011

Lifting platform



000 588 00 80 00 Vehicle lift

WS00.00-P-0040B

012

Support plate

 For front support to spring clamp plate (1).
Unscrew support plate (012) at right and left an equal distance.

 Model 906.132/134/136
In vehicles with vehicle lift support point at integral carrier (5).

013

Long support plate

 For front support at longitudinal member (2) and support at front rear spring bracket (6).
Can be used alternatively to front support to spring clamp plate (1).
Pull out long support plates (013) at right and left an equal distance.

 Model 906.132/134/136
In vehicles without a vehicle lift support point at the integral carrier (5) in the vicinity of the inner mounts of the semi-trailing arms.

014

V-block

 For rear support at front rear spring bracket (3) and rear support at longitudinal member (4).
Pull v-block (014) at right and left rear out an equal distance.

016

Ram

 Vehicles with heavy bodies and panel vans/crewbuses with a long wheelbase at the crossmember (7) should be supported with a prop (016).

017

Support drift


Model 900, 906
With soundproofingEnsure that support drift (017) does not make contact with bracket (8) of rear soundproofing. If necessary, loosen bracket (8), push towards the front as far as possible and retighten it.
Otherwise the brackets (8) of the rear soundproofing and the longitudinal members may be damaged.

 For front support to longitudinal member (2).
Unscrew support drift (017) at right and left an equal distance.