Model | 207.3 |
with code 3U1 (Headunit europe/CIS-states/Monoglei) | |
with code 505 (Radio 20 NTG5, not navigation-enabled) | |
except code 512 (COMAND APS with DVD changer) | |
except code 527 (COMAND APS with single DVD drive (with navigation)) | |
except code P44 (Parking package) | |
Model | 207.3 |
with code 3U1 (Headunit europe/CIS-states/Monoglei) | |
with code 522 (Audio 20 CD including preinstallation for Garmin® MAP PILOT) | |
except code 512 (COMAND APS with DVD changer) | |
except code 527 (COMAND APS with single DVD drive (with navigation)) | |
except code P44 (Parking package) | |
Model | 207.3 |
with code 3U1 (Headunit europe/CIS-states/Monoglei) | |
with code 531 (COMAND APS) | |
except code 512 (COMAND APS with DVD changer) | |
except code 527 (COMAND APS with single DVD drive (with navigation)) | |
except code P44 (Parking package) |
Connection scheme |
1 | Backup camera wiring harness |
1.1 | White 12-pin connector |
1.3 | White 4-pin connector |
1.4 | Black 2-pin coupling |
1.5 | Green fuse holder |
3 | White 12-pin plug |
A2 | Radio |
A40/3 | COMAND control unit |
B84/3 | Backup camera |
N10/2 | Rear SAM control unit with fuse and relay module |
W7 | Right wheelhouse trunk ground point |
X30/30 | Vehicle floor chassis CAN voltage distributor electrical connector |
br | Brown line |
ge | Yellow line |
ge/ws | Yellow/white line |
rt/bl | Red/blue line |
sw | Black line |
P54.65-5663-05
Routing diagram |
1 | Backup camera wiring harness |
1.1 | White 12-pin connector |
3 | White 12-pin plug |
A2 | Radio |
A40/3 | COMAND control unit |
B84/3 | Backup camera |
N10/2 | Rear SAM control unit with fuse and relay module |
W7 | Right wheelhouse trunk ground point |
X30/30 | Vehicle floor chassis CAN voltage distributor electrical connector |
br | Brown line |
ge | Yellow line |
ge/ws | Yellow/white line |
rt/bl | Red/blue line |
sw | Black line |
P54.65-5664-05
1 | Wrap insulating tape around wiring harness for reversing camera (1) starting at white 12-pin connector (1.1) along a length of 1400 mm (area A). |
2 | Route electrical line of reversing camera (B84/3) through specified opening into interior of trunk lid and clip reversing camera (B84/3) into place. |
P54.65-5091-03
3 | Place reversing camera wiring harness (1) in luggage compartment. |
4 | Connect white 12-pin plug (3) to white 12-pin connector (1.1). |
5 | Slip foam material over white, 12-pin plug (3) and white 12-pin connector (1.1). |
6 | Route wiring harness for reversing camera (1) from trunk lid over trunk lid hinge to left rear wheel well. |
Route wiring harness for reversing camera (1) between trunk lid hinge and left rear wheel well with sufficient clearance. |
7 | Fix reversing camera wiring harness (1) in place using cable ties (arrows B) and felt tape (arrow A). |
Fasten cable ties (arrows B) with retaining clip to trunk lid hinge. |
8 | Route red/blue line (RD/BU) along existing lines to rear SAM control unit with fuse and relay module and fix in place using cable ties. |
9 | Route brown line (BN) along existing lines to rear SAM control unit with fuse and relay module and fix in place using cable ties. |
10 | Route black line (BK) along existing lines into vehicle interior and fix in place using cable ties. |
Use a pull-through device. |
11 | Route twisted yellow line (YE) and yellow/white line (YE/WH) along existing lines into vehicle interior and fix in place using cable ties. |
Use a pull-through device. |
P54.65-5665-12
12 | Detach green fuse holder (1.5) from rear SAM control unit with fuse and relay module (N10/2). |
13 | Insert red/blue line (RD/BU) into contact cavity 4 (arrow C) of green fuse holder (1.5). |
Contact cavity 4 (arrow C) of the green fuse holder (1.5) is labeled. |
14 | Attach green fuse holder (1.5) to rear SAM control unit with fuse and relay module (N10/2). |
The slot on the rear SAM control unit with fuse and relay module (N10/2) is marked green. |
15 | Insert a 7.5 A fuse into slot 4 of the green fuse holder (1.5). |
16 | Tie back excess length of the red/blue line (RD/BU) and fix in place using cable ties. |
17 | Route brown line (BN) behind rear SAM control unit with fuse and relay module (N10/2) to right wheel arch trunk ground point (W7) and fix in place using cable ties. |
18 | Connect brown line (BN) to right wheel arch ground point in trunk (W7) Connecting. |
P54.65-5666-12
19 | Route black line (BK), twisted yellow line (YE) and yellow/white line (YE/WH) along existing lines into line ducts in driver footwell and fix in place using cable ties. |
P54.65-5094-11
20 | Connect twisted yellow line (YE) and yellow/white line (YE/WH) to vehicle floor chassis CAN potential distributor electrical connector (X30/30). |
21 | Route black line (BK) along ventilation duct to radio (A2) or COMAND controller unit (A40/3) and fix in place using felt tape. |
The black line (BK) is connected at a later stage to the radio (A2) or the COMAND controller unit (A40/3). |
P54.65-5667-12