an5465p0010a

Retrofitting ultrasonic backup aid

Type an · topic 54.65 · version 0103 · 2006-07-26

Applies to: MODEL 463 up to 1.9.96 Station wagon

Where it sits

Function group 2 Chassis › 54 Electrical system, equipment and instruments › 54.65 Parking assist — Series 463

EinPAS 28 Convenience system/driver assistance system › 28.15 Parking Assist › 28.15.3 Retrofitting/modification — Series 463

AN54.65-P-0010A

Retrofitting ultrasonic backup aid

10.12.98

MODEL 463 up to 1.9.96
Station wagon

Retrofitting ultrasonic backup aid

P54.65-2081-09

A43b7 Right outer sensor

A43b8 Right inner sensor

A43b9 Left inner sensor

A43b10 Left outer sensor

X58 Socket

X58/2 Microswitch for

backup assist cutoff

A44/1 Warning indicator

N62 Control module

W29/6 Rear pillar ground

Removal

1

Disconnect ground cable from battery

AR54.10-P-0003G

2

Remove bumper corners

AR88.20-P-0010G

3

Remove license plate illumination

Housing is clipped into bumper

4

Remove right-hand turn signal lamp

5

Remove trailer socket

Only if code E43 fitted

6

Remove right rear pillar paneling

Install

Use tools required for installation

Keyhole saw made of HSS-BI metal 32 mm

*WH58.30-Z-1001-34A

Keyhole saw holder 32 - 152 mm

*WH58.30-Z-1002-34A

Center bit 16 - 30.5 mm

*WH58.30-Z-1003-34A

Drill (electric/pneumatic)

*WE58.40-Z-1001-03A

Body saw (electric/pneumatic)

*WE58.40-Z-1004-03A

Wet/dry vacuum cleaner

*WE58.40-Z-1005-03A

7

Install warning indicator (A44/1) into rear pillar

Drill rear pillar paneling and isntall warning indicator with adhesive plate

AN54.65-P-0010-01A

8

Fit sensors into bumper

AN54.65-P-0010-03A

9

Install bumper corners

AR88.20-P-0010G

10

Connect sensor wiring harness and route into vehicle

Drill cable opening 25 mm in turn signal light housing

AN54.65-P-0010-02A

11

Preassemble wiring harness of backup assist cutoff

Only if code E43 fitted

Shop-make wiring harness

AN54.65-P-0010-06A

12

Install trailer socket with microswitch (X58s2)

Only if code E43 fitted

AN54.65-P-0010-05A

13

Install control module (N62) in rear pillar and connect

AN54.65-P-0010-04A

14

Connect ground cable to battery

AR54.10-P-0003G

15

Carry out function check

16

Install rear pillar paneling

17

Install right turn signal lamp

18

Install license plate lighting

Commercially available tools

Number

Designation

WH58.30-Z-1001-34A

HSS bimetal keyhole saw, dia. 32 mm (without mounting shaft and without drill bits)

WH58.30-Z-1002-34A

Keyhole saw holder dia. 32-152 mm

WH58.30-Z-1003-34A

Step drill bit dia. 16-30.5 mm

Workshop equipment

WE58.40-Z-1001-03A

Drill (electric/pneumatic)

WE58.40-Z-1004-03A

Body saw (electric/pneumatic)

WE58.40-Z-1005-03A

Wet/dry vacuum cleaner

Parts ordering notes

Part no.

Designation

Quantity

Group 82 (see EPC)

Parts see Parktronic system

1

Referenced documents