D88.40-1116-09
1 | Nuts | 4 | Hinges | 7 | Safety hook | ||
2 | Bolts | 5 | Stop buffer | 8 | Upper section of engine hood catch | ||
3 | Engine hood | 6 | Fender | 9 | Lower section of engine hood catch |
Danger ! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
| Check | ||
1 | Check installation position of engine hood (3) | ||
Gap dimension | |||
Feeler gauge | |||
Adjust | |||
2 | Loosen nuts (1) | ||
3 | Loosen bolts (2) | ||
4 | Set gap dimensions | ||
Center engine hood (3) between fenders (6). | |||
Gap dimension | |||
Feeler gauge | |||
5 | Tighten bolts (2) | Bolt, engine hood hinge to bodyshell | |
6 | Tighten nuts (1) | Collar nut, engine hood to hinge | |
7 | Adjust height offset between engine hood (3) and fender (6) by turning stop buffer (5) | ||
Height offset | |||
8 | Check whether engine hood catches properly, adjust if necessary | Close engine hood (3) and pull upward with a slight jerk. Unlock engine hood (3) and check whether safety hook (7) arrests correctly in engine hood lock bottom section (9). |
Test and adjustment values for gap dimensions |
Number | Designation | MODEL 900 except CODE T55 (Electric sliding door) | MODEL 900 with CODE T55 (Electric sliding door) | |||
BE60.00-N-1001-01C | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4,5 (0,5) | 4,5 (0,5) |
Engine hood to paneling next to headlamp | Dimension "B" | mm | 6,0 (0,5) | 6,0 (0,5) | ||
Picture | ||||||
Test and adjustment values for gap dimensions |
Number | Designation | MODEL 906.1/2 | MODEL 906.1/2 | |||
BE60.00-N-1001-01C | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4,5 (0,5) | 4,5 (0,5) |
Engine hood to paneling next to headlamp | Dimension "B" | mm | 6,0 (0,5) | – | ||
Picture | ||||||
Test and adjustment values for gap dimensions |
Number | Designation | MODEL 906.6/7 except CODE T55 except CODE T56 (Electric sliding door) except CODE XM0 (Facelift) | Model 906.6/7 except CODE T55 except T56 (Electric sliding door) with CODE XM0 (Facelift) | |||
BE60.00-N-1001-01C | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4,5 (0,5) | 4,5 (0,5) |
Engine hood to paneling next to headlamp | Dimension "B" | mm | 6,0 (0,5) | – | ||
Picture | ||||||
Test and adjustment values for gap dimensions |
Number | Designation | MODEL 906.6/7 with CODE T55/T56 (Electric sliding door) except code XM0 (Facelift) | Model 906.6/7 with CODE T55/T56 (Electric sliding door) with CODE XM0 (Facelift) | |||
BE60.00-N-1001-01C | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4,5 (0,5) | 4,5 (0,5) |
Engine hood to paneling next to headlamp | Dimension "B" | mm | 6,0 (0,5) | – | ||
Picture | ||||||
Test and adjustment values for gap dimensions |
Number | Designation | MODEL 906.6/7 except CODE T55 except CODE T56 (Electric sliding door) except CODE XM0 (Facelift) | Model 906.6/7 except CODE T55 except T56 (Electric sliding door) with CODE XM0 (Facelift) | ||
BE60.00-N-1002-01C | Height offset | Engine hood to fender | mm | 0,8 | 0,8 |
129 589 03 21 00
Feeler gauge
Henviste dokumenter
- ar6000d070001h
- as0000z001101a Fare for personskade pga. fastklemning eller knusning af fingre ved af-, påmontering og indstillingsarbejde på motorhjelm og bagklap, døre, dæksler og soltag.