Shown on vehicle with code JS1 (360° camera) and with code EZ7 (Active Parking Assist) |
1 | Front bumper |
2 | Electrical connector |
3 | Electrical wiring harness |
4 | Impact absorber |
5 | Radiator trim |
6 | Electrical wiring harness |
B84 | Front 360° camera |
S88.20-4530-06
7 | Towing eye cover |
8 | Cover |
S88.20-4548-06
S88.20-4549-09
Shown on left side of vehicle |
9 | Mounting clamp | 10 | Cover |
S88.20-4550-09
Shown on left side of vehicle |
11 | Mounting clamp | 13 | Upper trim piece | |
12 | Bracket | 14 | Lower trim piece |
S88.20-4551-09
15 | Mounting clamp | 17 | Expansion rivet | 19 | Left reinforcement | ||
16 | Cover | 18 | Screw | 20 | Bracket |
S88.20-4552-09
21 | Mounting clamp | 23 | Expansion rivet | 25 | Right reinforcement | ||
22 | Cover | 24 | Screw | 26 | Bracket |
27 | Air duct insert |
S88.20-4553-06
28 | Lower trim piece |
S88.20-4554-06
| Remove | ||
1 | Remove front bumper (1). | ||
| Disassemble/assemble | ||
2 | Remove license plate number. | ||
3 | Remove license plate holder. | ||
4 | Remove license plate bracket. | ||
5 | Disconnect electrical connection (2). | Model 447.8 | |
6 | Remove electrical wiring harness (3) from the impact absorber (4). | Model 447.8 | |
7 | Remove impact absorber (4). | ||
8 | Remove front 360° camera (B84) and front 360° camera bracket. | Model 447.8 | |
9 | Remove radiator grille (5). | ||
10 | Remove PARKTRONIC sensors in front bumper (1). | Model 447.8 | |
11 | Remove radar sensor. | Model 447.8 | |
12 | Remove electrical wiring harness (6) from front bumper (1). | Model 447.8 | |
13 | Remove towing eye cover (7). | ||
14 | Release catch hooks (arrows B) and remove cover (8). | Assembly: Ensure that the catch hooks (arrows B) are seated correctly. | |
15 | Remove mounting clamps (9) from left and right cover (10). | ||
16 | Release catch hooks (arrows C) and remove left and right cover (10). | Assembly: Observe that the catch hooks (arrows C) are seated correctly. | |
17 | Remove mounting clamps (11) from the left and right cover (10). | ||
18 | Remove brackets (12) from the left and right cover (10). | ||
19 | Release catch hooks (arrows D) and remove top trim piece (13) from the left and right cover (10). | Assembly: Ensure that the catch hooks (arrows D) are seated correctly. | |
20 | Release catch hooks (arrows E) and remove bottom trim piece (14) from the left and right cover (10). | Assembly: Ensure that the catch hooks (arrows E) are seated correctly. | |
21 | Remove mounting clamps (15). | ||
22 | Release catch hooks (arrows F) and remove cover (16). | Assembly: Ensure that the catch hooks (arrows F) are seated correctly. | |
23 | Remove expansion rivets (17). | ||
24 | Remove screw (18). | ||
25 | Remove bracket (20). | ||
26 | Release catch hooks (arrows G) and remove left reinforcement (19). | Assembly: Check that the catch hooks (arrows G) are seated correctly. | |
27 | Remove mounting clamps (21). | ||
28 | Release catch hooks (arrows H) and remove cover (22). | Assembly: Ensure that the catch hooks (arrows H) are seated correctly. | |
29 | Remove expansion rivets (23). | ||
30 | Remove screw (24) . | ||
31 | Remove bracket (26). | ||
32 | Release catch hooks (arrows I) and remove right reinforcement (25). | Assembly: Ensure that the catch hooks (arrows I) are seated correctly. | |
33 | Release catch hooks (arrows J) and remove air duct insert (27). | Assembly: Ensure that the catch hooks (arrows J) are seated correctly. | |
34 | Release catch hooks (arrows K) and remove bottom trim piece (28). | Assembly: Ensure that the catch hooks (arrows K) are seated correctly. | |
35 | Assemble in the reverse order. | ||
| Install | ||
36 | Install front bumper (1). |