Adjust evenness, installation depth and stop of sliding door · ar7216d102302i · Mercedes-Benz WIS

AR72.16-D-1023-02I

Adjust evenness, installation depth and stop of sliding door

MODEL	900.6
	with CODE D03 (Roof and rear-end doors, high version)
	with CODE T16 (Right load compartment sliding door)
MODEL	906.6/7
	with CODE D03 (Roof and rear-end doors, high version)
	with CODE T16 (Right load compartment sliding door)
MODEL	906.6/7
	with CODE D03 (Roof and rear-end doors, high version)
	with CODE T19 (Sliding door left)

 Sliding doors

Number	Designation		MODEL 900	MODEL 906.6/7
BA72.16-N-1003-01A	Bolt, guide wedge to sliding door	Nm	8	8

 Sliding doors

Number	Designation		MODEL 900	MODEL 906.6/7
BA72.16-N-1004-01A	Bolt, lower carriage to sliding door	Nm	23	23

 Sliding doors

Number	Designation			MODEL 900	MODEL 906.6/7
BA72.16-N-1009-01A	Bolt, sliding door stop on sliding door	8.8	Nm	23	23
		10.9	Nm	32	32

 Sliding doors

Number	Designation		MODEL 900	MODEL 906.6/7
BA72.16-N-1017-01A	Bolt, lock striker to C-pillar	Nm	20	20

Adjust evenness, installation depth and stop of sliding door

129 589 03 21 00

Feeler gauge

Adjust flatness of sliding door in relation to B-pillar

1	Loosen bolts (12, 13).

2	Adjust flatness by moving upper and lower carriage.

 Adjust flatness so that sliding door is flush with B-pillar or recessed up to 1 mm.

3	Tighten bolts (12, 13) .

D72.16-1218-01

D72.16-1219-01

Adjust flatness of sliding door in relation to C-pillar

4	Loosen bolts (8).

5	Adjust flatness by horizontally moving lock striker (8).

 Adjust flatness so that sliding door is flush with C-pillar or recessed up to 1 mm.

6	Tighten bolts (8) .

D72.16-1224-01

7	Loosen locking bolt (15).

8	Adjust flatness by horizontally adjusting striker pin (15).

 Adjust flatness so that sliding door is flush with C-pillar or recessed up to 1 mm.

9	Tighten striker pin (15).

D72.16-1226-01

Adjusting actuator on lower sliding carriage (except code T55 (Electrical actuation for right sliding door) except code T56 (Electrical actuation for left sliding door))

10	Completely open sliding door and arrest in end position.

11	Loosen bolts (18).

12	Adjust position by vertically adjusting (arrow) lower sliding carriage with  feeler gauge.

 The latch (16) should arrest in the center of the rotating sleeve (17).
The lower carriage should not chafe against the protective foil on the entrance. Clearance should be 1 - 1.5 mm. Measured from the front end of the protective foil.

13	Tighten bolts (18) .

D72.16-1244-01

D72.16-1245-01

Adjust guide wedge
 Never adjust sliding door (gap dimensions and ridge pattern) with guide wedges (2). The guide wedges (2) are only fastening components arresting the sliding door while driving.
Do not loosen bolts (3).

14	Adjust position of guide wedge (2) in relation to slider (4).

15	Close sliding door.

 This centers the guide wedges (2) at the sliding blocks (4). Install guide wedge crash bolts (2) in mounting hole for sliding blocks (4) without colliding.

16	Check flatness of sliding door in relation to B-pillar.

17	Open sliding door.

18	Tighten bolts (1) .

D72.16-1220-01

Adjust sliding door stop at front sliding door

19	Detach sliding door stop (14) at top and bottom of sliding door.

20	Open sliding door and arrest in end position.

21	Adjust upper and lower sliding door stop (14) with a gap of 2 to 3 mm in relation to C-pillar with  feeler gauge and tighten.

 Adjust gap at upper and lower sliding door stop (14) to same dimension.

D72.16-1221-01

Adjust upper and lower stop on rear sliding door

22	Adjust upper and lower stop (19).

 Adjust stops (19) so that they overlap C-pillar approx. 1 to 1.5 mm. If they are adjusted too loosely, rattling noises can occur, if adjusted too tightly the door can be subject to tensions.

D72.16-1243-01