MODEL | 900.6 |
with CODE D03 (Roof and rear-end doors, high version) | |
with CODE T16 (Right load compartment sliding door) | |
MODEL | 906.6/7 |
with CODE D03 (Roof and rear-end doors, high version) | |
with CODE T16 (Right load compartment sliding door) | |
MODEL | 906.6/7 |
with CODE D03 (Roof and rear-end doors, high version) | |
with CODE T19 (Sliding door left) |
Test and adjustment values for gap dimensions |
Number | Designation | MODEL 900 except CODE T55 (Electric sliding door) | MODEL 906.6/7 except CODE T55 except CODE T56 (Electric sliding door) except CODE XM0 (Facelift) | |||
BE60.00-N-1007-01C | Gap dimension | Upper sliding door | Dimension "O" | mm | 5,5 (1,5) | 5,5 (1,5) |
Lower sliding door | Dimension "P" | mm | 5,5 (1,5) | 5,5 (1,5) | ||
Sliding door to B-pillar | Dimension "Q" | mm | 7,0 (1,5) | 7,0 (1,5) | ||
Sliding door to C-pillar | Dimension "R" | mm | 7,0 (1,5) | 7,0 (1,5) | ||
Picture | ||||||
Test and adjustment values for gap dimensions |
Number | Designation | Model 906.6/7 except CODE T55 except T56 (Electric sliding door) with CODE XM0 (Facelift) | MODEL 906.6/7 with CODE T55/T56 (Electric sliding door) except code XM0 (Facelift) | |||
BE60.00-N-1007-01C | Gap dimension | Upper sliding door | Dimension "O" | mm | 5,5 (1,5) | 5,5 (1,5) |
Lower sliding door | Dimension "P" | mm | 5,5 (1,5) | 5,5 (1,5) | ||
Sliding door to B-pillar | Dimension "Q" | mm | 7,0 (1,5) | 1,0 | ||
Sliding door to C-pillar | Dimension "R" | mm | 7,0 (1,5) | 6 (–1,0) | ||
Picture | ||||||
129 589 03 21 00
Feeler gauge
A | Ridge pattern |
O | Upper gap dimension |
P | Lower gap dimension |
Q | B-pillar gap dimension |
R | C-pillar gap dimension |
D72.16-1214-02
Adjust ridge pattern
1 | Loosen locknuts (5) and adjust rear ridge pattern A by lifting or lowering sliding door on adjusting screw (6). |
2 | Tighten jam nuts (5). |
D72.16-1215-01
3 | Loosen bolts (7, 9) on upper and lower sliding carriage. |
4 | Match front ridge pattern A at upper carriage by lifting or lowering sliding door. |
5 | Tighten bolts (7, 9) to specified torque. |
D72.16-1216-01
Do not lift or pull down sliding door over locking eye. When the ridge pattern coincides, the bottom and top gap dimensions on the sliding door should be within the specified tolerance range. For optical reasons, a slightly wedge-shaped gap dimension at the top and bottom is preferable to a ridge offset.
D72.16-1223-01
D72.16-1225-01
6 | Loosen Torx bolts (8) for locking eye as well as striker bolt (15) for auxiliary lock and adapt to modified door adjustment by moving lock striker or striker pin (15) vertically (arrow). |
7 | Tighten bolts (8) and striker pin (15) to specified torque. |
Adjust B-pillar gap dimension and C-pillar gap dimension
8 | Loosen bolts (10) and adjust B-pillar gap dimension and C-pillar gap dimension as well as minimum distance between sliding door and center guide rail by horizontally moving center carriage (11) with feeler gauge. |
When adjusting ensure that, during the closing procedure (catch in door lock), the sliding door does not collide with the center guide rail. The specified minimum distance from the sliding door to the center guide rail is prior to the adjustment of the C-pillar gap dimension. |
9 | Tighten bolts (10) to specified torque. |
D72.16-1217-01