ar7212p0104eg

Remove/install rear door inner door panel

Type ar · emne 72.12 · version 0100 · 2010-02-09

Gælder for: MODEL 212 with CODE (Z04) Light armoring with rear power window

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 3 Karrosseri › 72 Døre › 72.12 Bagdør — Serie 212

EinPAS 35 Karrosseri/ramme/monteringsdele › 35.35 Dør › 35.35.46 Bagdør — Serie 212

AR72.12-P-0104EG

Remove/install rear door inner door panel

27.1.10

MODEL 212 with CODE (Z04) Light armoring
with rear power window

Remove/install rear door inner door panel

P72.12-2830-09

1 Door wiring harness

2 Line bracket

3 Grommet

4 Grommet

5 Electrical connector

6 Electrical connector

7 Electrical connector

8 Electrical connector

9 Adhesive tape

10 Electrical connector

B48/9 Left rear door pressure sensor

B48/10 Right rear door pressure sensor

H4/3h2 Left rear door basic speaker

H4/4h2 Right rear door basic speaker

N69/3 Left rear door control unit

N69/4 Right rear door control unit

X35/3 Left rear door electrical connector

X35/4 Right rear door electrical connector

11 Cable tie

12 Cable tie

13 Bolts

14 Grommet

15 Grommet

16 Inner door panel

A2/39 Left rear door KEYLESS-GO antenna

A2/41 Right rear door KEYLESS-GO antenna

Remove/install rear door inner door panel

P72.12-2833-04

16 Inner door panel

17 Grommet

18 Grommet

Remove/install

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

1

Completely open crank window

2

Remove rear door lining

AR72.12-P-1010CW

3

Disconnect electrical connector on left rear door (X35/3) or electrical connector on right rear door (X35/4)

4

Unclip grommets (3, 4)

5

Pull door wiring harness (1) out of rear door

6

Release lugs (arrows) on wiring harness bracket (2)

7

Remove line bracket (2) from grommet (3)

Installation: Installation position must be observed.

8

Disconnect electrical connectors (5) from left rear door control unit (N69/3) or electrical connectors from right rear door control unit (N69/4)

9

Disconnect electrical connector (6) from left rear door KEYLESS-GO antenna (A2/39) or right rear door KEYLESS-GO antenna (A2/41)

Only on vehicles with code (889) Keyless Go.

10

Disconnect electrical connector (7) from left rear door basic speaker (H4/3h2) or right rear door basic speaker (H4/4h2)

11

Disconnect electrical connector (8) from left rear door pressure sensor (B48/9) and right rear door pressure sensor (B48/10)

Only on vehicles with code (293) right and left rear sidebag.

12

Remove adhesive tape (9) over connector (10) from inner door panel (16)

13

Disconnect electrical connector (10)

14

Separate cable tie (11)

Installation: Observe installation position, replace cable tie (11).

15

Cut cable tie (12)

Only on vehicles with code (889) Keyless Go.

Installation: Observe installation position, replace cable tie (12).

16

Unclip electrical wiring harness from inner door panel (16)

Installation: Installation position must be observed.

17

Remove grommets (14, 15, 17, 18) from inner door panel (16)

18

Remove bolts (13)

*BA72.12-P-1006-01O

19

Remove inner door panel (16) from door, simultaneously guide electrical lines, inside door handle Bowden cable and locking pin Bowden cable through

20

Install in the reverse order

Rear door

Number

Designation

Model
212 with code Z04

BA72.12-P-1006-01O

Bolt, inner door panel to rear door

Nm

5

Henviste dokumenter