Remove/install side paneling in trunk

AR68.30-P-4800LW

Remove/install side paneling in trunk

06.12.2019

Model

205.0/1/3

Shown on model 205.0 (except 205.013/047/053/054) with code 550 (trailer hitch) and except code 287 (folding seat backrests in the rear passenger compartment) and except code 30P (Stowage Space Package)

1

Cover

6

Seal

2

Mounting clip

7

Bracket

3

Trunk floor front section

8

Electrical connector

4

Expansion rivet

E18/4

Right luggage compartment lamp

5

Rear center section paneling

S62/24

Trailer hitch release switch

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

 Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.

AS00.00-Z-0035-01A

Topical note

General information on handling vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system

AH00.00-Z-0300-01A

Notes on HANDS-FREE ACCESS

AH80.61-P-0001-01A

 

Remove/install

1

Remove rear-end center section paneling (5).

AR68.30-P-4785LW

2.1

Remove trunk floor front section (3).

Model 205.0 (except 205.013/047/053/054), 205.1 (except 205.147), 205.3

Model 205.0 (except 205.013/047/053/054), 205.1 (except 205.147)

AR68.80-P-0005LWW

 Screw/bolt for tie-down eye

*BA68.50-P-1001-03I

2.2

Remove high-voltage battery cover.

Model 205.013/047/053/054/147

AR68.80-P-6000LWH

3

Remove retaining clips (2).

 Dismantling tool

*000589956300

4.1

Remove expansion rivet (4).

Model 205.0 (except 205.013/047/053/054), 205.1 (except 205.147), 205.3
except code 287 (Folding seat backrests in rear passenger compartment)
except code 30P (Stowage Space package)

 Dismantling tool

*000589956300

4.2

Remove tie-down eye.

Model 205.0 (except 205.013/047/053/054), 205.1 (except 205.147), 205.3
with code 287 (Folding seat backrests in rear passenger compartment)
Model 205.0 (except 205.013/047/053/054), 205.1 (except 205.147), 205.3
with code 30P (Stowage Space package)
Model 205.013/047/053/054/147

 Screw/bolt for tie-down eye

*BA68.50-P-1001-03I

5

Remove the bracket (7).

Model 205.0 (except 205.013/053/054), 205.1

6

Release trim (1) until the electrical connector (8) is accessible.

Model 205.0/1/3
with code 550 (Trailer coupling)
When removing left paneling (1).

 Installation: Ensure that the seal (6) is seated correctly.

7

Disconnect electrical connector (8) from the trailer hitch release switch (S62/24).

Model 205.0/1/3
with code 550 (Trailer coupling)
When removing left paneling (1).

8

Release trim (1) until the electrical connector of the right trunk lamp (E18/4) is accessible.

When removing right paneling (1).

 Installation: Ensure that the seal (6) is seated correctly.

9

Disconnect electrical connector for right trunk lamp (E18/4).

When removing right paneling (1).

10

Remove left and right trim (1) from the rear toward the front in the direction of the arrow.

 Installation: Ensure that the seal (6) is seated correctly.

11

Install in the reverse order

 Cargo retainers

Number

Designation

Model 205

BA68.50-P-1001-03I

Screw/bolt for tie-down eye

Nm

24