Serier
da
ar6320w110203a
Install A-pillar outer section
Type ar · emne 63.20 · version 0103 · 2006-07-25
Gælder for: BODY 374.850 in MODEL 374.4 BODY 374.860 in MODEL 374.5 BODY 374.870 in MODEL 374.6 BODY 375.810 in MODEL 375.3 BODY 375.830 in MODEL 375.1 BODY 375.840 in MODEL 375.4 BODY 940.890 /899 in MODEL 950.5 /6, 952.5 /6, 953.6, 954.5 BODY 944.890 in MODEL 940.2 /3, 942.1 /3, 943.1 /3, 944.0 /2 BODY 944.899 in MODEL 944.0 /2 BODY 958.860 in MODEL 958.0 BODY 958.870 in MODEL 958.2 BODY 958.880 in MODEL 958.4 BODY 972.890 /899 in MODEL 970, 972, 974, 975, 976
Ikke tilgængelig på “da”; vises på Engelsk.
Placering
Funktionsgruppe 3 Karrosseri › 63 Sidevæg › 63.20 Stolper — Serie 374 (modeller 4**, 5**, 6**, 850, 860, 870) · Serie 375 (modeller 1**, 3**, 4**, 810, 830, 840) · Serie 940 (modeller 2**, 3**, 890, 899) · Serie 942 (modeller 1**, 3**) · Serie 943 (modeller 1**, 3**) · Serie 944 (modeller 0**, 2**, 890, 899) · Serie 950 (modeller 5**, 6**) · Serie 952 (modeller 5**, 6**) · Serie 953 (modeller 6**) · Serie 954 (modeller 5**) · Serie 958 (modeller 0**, 2**, 4**, 860, 870, 880) · Serie 970 · Serie 972 · Serie 974 · Serie 975 · Serie 976
EinPAS 35 Karrosseri/ramme/monteringsdele › 35.34 Sidevæg › 35.34.45 Stolpe — Serie 374 (modeller 4**, 5**, 6**, 850, 860, 870) · Serie 375 (modeller 1**, 3**, 4**, 810, 830, 840) · Serie 940 (modeller 2**, 3**, 890, 899) · Serie 942 (modeller 1**, 3**) · Serie 943 (modeller 1**, 3**) · Serie 944 (modeller 0**, 2**, 890, 899) · Serie 950 (modeller 5**, 6**) · Serie 952 (modeller 5**, 6**) · Serie 953 (modeller 6**) · Serie 954 (modeller 5**) · Serie 958 (modeller 0**, 2**, 4**, 860, 870, 880) · Serie 970 · Serie 972 · Serie 974 · Serie 975 · Serie 976
AR63.20-W-1102-03A
Install A-pillar outer section
Commercially available tools
Number
Designation
WH58.30-Z-1003-01A
Electrode miller
WH58.30-Z-1003-02A
Clamping pliers
WH58.30-Z-1031-02A
C-clamp
WH58.30-Z-1001-03A
Round wire brush, braided, dia. 70 mm
WH58.30-Z-1024-04A
Abrasive disk, dia. 115 mm, 80 m/s (max. 13,250 rpm)
WH58.30-Z-1001-40A
Tarp (fire-resistant)
WE58.40-Z-1001-02A
Inert gas welder
WE58.40-Z-1002-02A
Spot welder
WE58.40-Z-1001-03A
Drill (electric/pneumatic)
WE58.40-Z-1003-03A
Angle grinder (electric/pneumatic)
WE58.40-Z-1005-03A
Wet/dry vacuum cleaner
1 Fit A-pillar outer section with straightening tool (arrows) and fasten with clamping pliers.
2 Tack A-pillar outer section at several points.
3 Remove straightening tool
4 Fit door (check gaps and transitions)
5 Install straightening tool (arrows).
6 Weld in A-pillar outer section in areas A and B with .
7 Weld in A-pillar outer section in areas C to E with .
8 Weld in A-pillar outer section in areas F and G with .
9 Weld in A-pillar outer section in area H with .
10 Weld in A-pillar outer section in areas I to K with .
11 Clean all weld joints with wire brush.
12 Only grind slightly in area I (visible seam).
Do not grind down weld joints in areas which are not visible for reasons of operating stability and cost.
