ar4110p008502msa

Measure absolute angle at front and rear propeller shafts

Type ar · emne 41.10 · version 0100 · 2018-05-17

Gælder for: Model 257

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 2 Chassis › 41 Kardanaksel › 41.10 Kardanaksel — Serie 257

EinPAS 17 Drivstreng/aksel › 17.40 Kardanaksel › 17.40.30 Kardanaksel drivmekanisme/firehjulstræk — Serie 257

AR41.10-P-0085-02MSA

Measure absolute angle at front and rear propeller shafts

Notes on measuring the drive shaft articulation angle

AH41.10-P-0002-01LF

000 588 04 19 00 Articulation angle inclinometer

WS26.00-P-0140B

Model

257

Measure absolute angle at front and rear propeller shafts

Measurement of angle 2 at front half of propeller shaft
All four angles should be measured in succession without interruption. An angle that has already been measured can be measured a second time if required. To do so, with the Measurement menu displayed, press the STEP button repeatedly until the display indicates Ready to measure the relevant angle.

1

Clean contact surface of test adapter (3) of sensor (020a) at front half of propeller shaft (1).



2

Position test adapter (3) vertically from below onto front half of propeller shaft (1) and align.



3

Place sensor (020a) from above onto test adapter (3).


When each measurement is taken, the side of the sensor (020a) at which the spiral cable (020b) is connected must point in the direction of travel.
False measurements can occur otherwise.


The sensor (020a) must be aligned vertically with the spirit level.
If the sensor (020a) is not positioned vertically from below, the fault message "Y-positional error - sensor ??" appears. The measured angle cannot be saved.


P41.10-2391-02

Measure absolute angle at front and rear propeller shafts

The value measured is shown on the display.

4

Press SAVE button.


The values are saved.


Measurement values on display message for angle piece 2: Display, e.g. 2.18°

P41.10-2078-01

Measure absolute angle at front and rear propeller shafts

A confirmation message appears briefly.

Display message confirmation

P41.10-2076-01

Measure absolute angle at front and rear propeller shafts

5

Remove sensor (020a) and test adapter (3) from front half of propeller shaft (1).


P41.10-2391-02

Measure absolute angle at front and rear propeller shafts

The display then indicates that the device is ready for the next measurement (angle 3).

Ready for measurement display message for angle 3

P41.10-2079-01

Measure absolute angle at front and rear propeller shafts

Measurement of angle 3 at rear half of propeller shaft

6

Clean contact surface of sensor (020a) at rear half of propeller shaft (2).



7

Position sensor (020a) vertically from below on rear half of propeller shaft (2) and press on firmly.


When each measurement is taken, the side of the sensor (020a) at which the spiral cable (020b) is connected must point in the direction of travel.
False measurements can occur otherwise.


P41.10-2359-01

Measure absolute angle at front and rear propeller shafts

The value measured is shown on the display.

8

Press SAVE button.


The values are saved.


Measurement values on display message for angle piece 3: Display, e.g. 2.76°

P41.10-2080-01

Measure absolute angle at front and rear propeller shafts

A confirmation message appears briefly.

Display message confirmation

P41.10-2076-01

Measure absolute angle at front and rear propeller shafts

The display then indicates that the device is ready for the next measurement (angle 4).

Ready for measurement display message for angle 4

P41.10-2081-01

Measure absolute angle at front and rear propeller shafts

9

Remove sensor (020a) from rear half of propeller shaft (2).


P41.10-2359-01

Henviste dokumenter