Check vehicle level at front and rear axle with electronic inclinometer, adjust if necessary

AR40.20-P-0304-02MFA

Check vehicle level at front and rear axle with electronic inclinometer, adjust if necessary



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B

Assign suspension dataModel 247

AR40.20-P-0203MB

Assign suspension dataModel 177

AR40.20-P-0203MFA

Assign suspension dataModel 118

AR40.20-P-0203MFI

Assign suspension dataModel 247

AR40.20-P-0203MB

Assign suspension dataModel 177

AR40.20-P-0203MFA

Assign suspension dataModel 118

AR40.20-P-0203MFI



Connect/disconnect diagnostic unit

AD00.00-P-2000-06MFA



Check and correct the adjustment of the headlamps

Model 118

AP82.10-P-8260Y



Check and correct the adjustment of the headlamps

Model 247

AP82.10-P-8260AO



Check and correct the adjustment of the headlamps

Model 177

AP82.10-P-8260N

Model

118, 177, 247

Repair materials

Number

Designation

Order number

BR00.45-Z-1025-04A

Cleaner

A 005 989 19 71

Check

1

Vehicle level inclinometer

2

Measuring sensor

3

Connecting cable

Shown on rear axle on model 177 with code U55 (Multi-link axle)

4

Cover

1

Model 118, 177, 247
with code U55 (Multi-link axle)
Unclip and remove cover (4) on left and right side of vehicle.

 Installation: Ensure that cover (4) is properly seated.

2

Model 118, 177, 247
with code U55 (Multi-link axle)
Measuring points .

 In order to avoid a measuring error.

3

Model 118, 177, 247
with code U55 (Multi-link axle)
Position measuring sensor (2) at measuring points on lower control arm at rear left and save measured value.

 Measuring point 1.

4

Model 118, 177, 247
with code U55 (Multi-link axle)
Position measuring sensor (2) at measuring points on lower control arm at rear right and save measured value.

 Measuring point 4.

Shown on rear axle on model 177 with code U54 (Torsion-beam axle)

5

Cover

5

Model 118, 177, 247
with code U54 (Compound-link axle)
Check for correct seating of cover (5).

6

Model 118, 177, 247
with code U54 (Compound-link axle)
Measuring points .

 In order to avoid a measuring error.

7

Model 118, 177, 247
with code U54 (Compound-link axle)
Position measuring sensor (2) at measuring points of cover at rear left and save measured value.

 Press on measuring sensor (2) firmly so that cover makes contact with axle carrier.

 Measuring point 1.

8

Model 118, 177, 247
with code U54 (Compound-link axle)
Position measuring sensor (2) at measuring points of cover at rear right and save measured value.

 Press on measuring sensor (2) firmly so that cover makes contact with axle carrier.

 Measuring point 4.

Show on front axle on model 177

9

Position measuring sensor (2) at measuring points on lower control arm at front left and save measured value.

 Measuring point 3.

10

Position measuring sensor (2) at measuring points on lower control arm at front right and save measured value.

 Measuring point 2.

Show on front axle on model 118

11

Check maximum permissible difference in vehicle level between left and right side of vehicle at front axle.

 The specified test tolerance applies only when checking the vehicle level but not for calibration.

12

Check maximum permissible difference in vehicle level between left and right side of vehicle at rear axle.

 The specified test tolerance applies only when checking the vehicle level but not for calibration.

13

Model 118, 177, 247
with code U55 (Multi-link axle)
Install cover on left and right side of vehicle.

14

Calibrate vehicle level using vehicle diagnosis system.

When the vehicle level is outside the test tolerance.

15

Check and correct headlamp adjustment.

When the vehicle level is calibrated.