ar4020p0301fr

Check vehicle level at front and rear axle with electronic inclinometer, adjust if necessary

Type ar · emne 40.20 · version 0102 · 2018-09-18

Gælder for: Model 257, 290

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 2 Chassis › 40 Hjul, undervognsudmåling › 40.20 Undervognsudmåling — Serie 257 · Serie 290

EinPAS 20 Undervogn › 20.10 Undervognsudmåling › 20.10.20 diagnose/kontrol/udmåling/indstilling — Serie 257 · Serie 290

AR40.20-P-0301FR

Check vehicle level at front and rear axle with electronic inclinometer, adjust if necessary

12.09.2018

Model

257, 290

Check vehicle level at front and rear axle with electronic inclinometer, adjust if necessary

086

Inclinometer

086a

Measuring sensor

P40.20-0318-01

Check vehicle level at front and rear axle with electronic inclinometer, adjust if necessary

Shown on model 257 on front axle

1

Spring control arm

086a

Measuring sensor

086b

Connecting cable

a

Measuring range

P40.20-2422-06

Check vehicle level at front and rear axle with electronic inclinometer, adjust if necessary

Shown on model 257 on rear axle, except code 489 (AIR BODY CONTROL)

2

Rear axle shaft

086a

Measuring sensor

086b

Connecting cable

b

Measuring range

P40.20-2423-06

Check

1

Check condition of vehicle.

Before the vehicle level check, it must be ensured that none of the suspension components are damaged or exhibit wear.

For the vehicle level check, all vehicle parts must be installed and the vehicle completed and in a ready to drive condition. The vehicle must not be loaded.

2

Check and correct tire pressure.

AP40.15-P-4061A

3

Drive the vehicle onto measuring station and secure using parking brake.

4

Unlock turn and slip plates.

5

Clean measuring ranges (a, b).

6

Place measuring sensor (086a) in measuring range (a) and measure vehicle level at measuring point 1 (front left) and measuring point 2 (front right).

000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B

Assign suspension dataModel 290

AR40.20-P-0203FX

Assign suspension dataModel 257

AR40.20-P-0203FR


The connecting cable (086b) for the measurement sensor (086a) must face towards the vehicle center.
Otherwise the measurement will be inaccurate.

Save measured values.

7

Place measuring sensor (086a) in measuring range (b) and measure vehicle level at measuring point 3 (rear left) and measuring point 4 (rear right).

000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B

Assign suspension dataModel 290

AR40.20-P-0203FX

Assign suspension dataModel 257

AR40.20-P-0203FR


The connecting cable (086b) for the measurement sensor (086a) must face towards the vehicle center.
Otherwise the measurement will be inaccurate.

Save measured values.

8

Check maximum permissible difference in vehicle level between left and right side of vehicle at front axle.

Assign suspension data
Model 290

AR40.20-P-0203FX

Assign suspension dataModel 257

AR40.20-P-0203FR

The specified test tolerance applies only when checking the vehicle level but not for calibration.

9

Check maximum permissible difference in vehicle level between left and right side of vehicle at rear axle.

Assign suspension data
Model 290

AR40.20-P-0203FX

Assign suspension dataModel 257

AR40.20-P-0203FR

The specified test tolerance applies only when checking the vehicle level but not for calibration.

Adjust

10

Calibrate vehicle level using vehicle diagnosis system.

Model 257, 290
with code 489 (AIR BODY CONTROL)
When the vehicle level is outside the test tolerance.

AD00.00-P-2000-06FR

11

Check and correct headlamp adjustment.

Only if the vehicle level has been calibrated.

Model 290
with code 489 (AIR BODY CONTROL)

AP82.10-P-8260O

Model 257
with code 489 (AIR BODY CONTROL)

AP82.10-P-8260L

Henviste dokumenter