Remove/install radius rod · ar3520p0111v · Mercedes-Benz WIS

AR35.20-P-0111V

Remove/install radius rod

10.11.11

MODEL 171

P35.20-2145-06

Shown on model 171.442

1 Bolts

3 Torque strut

4 Rear axle carrier

5 Thrust arm

6 Differential

Modification notes

	Self-locking bolt, rear axle carrier rear rubber bushing to frame floor	Model 171	*BA35.10-P-1002-01A
2.5.07	Self-locking nut, strut rod to rear axle carrier, M12		*BA35.20-P-1001-03A
2.5.07	Self-locking nut, strut rod to wheel carrier, M12		*BA35.20-P-1002-03A

 	Remove/install
Danger!	Risk of death caused by vehicle slipping or toppling off the lifting platform.	Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.	AS00.00-Z-0010-01A
	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
 Installation	Only tighten nuts and bolts of chassis components when vehicle is in a ready-to-drive condition.
1	Raise vehicle with vehicle lift		AR00.60-P-1000V
2	Secure vehicle on vehicle lift
3	Remove wheel.
	Remove/install wheels, rotate if necessary		AP40.10-P-4050V
4	Detach thrust arm (5) from wheel carrier		*BA35.20-P-1003-05A
5	Detach torque strut (3) from wheel carrier		*BA35.20-P-1002-03A
			*202589001000
6	Support rear axle carrier (4) and secure to prevent it from falling down		*140589016200
		Transmission jack 2.0-7.0 t gotis://H_00.10_01.0
7	Loosen bolts (1) and lower rear axle carrier (4)		*BA35.10-P-1001-01A
			*BA35.10-P-1002-01A
8	Detach torque strut (3) from rear axle carrier (4)		*BA35.20-P-1001-03A
			*129589010300
9	Install in the reverse order
10	Perform wheel alignment check		AR40.20-P-0200V

 Rear axle carrier

Number	Designation				Model 171


BA35.10-P-1001-01A	Self-locking bolt, front rear axle carrier rubber bushing to frame floor	-		Nm	-
		with Ø 24 mm bolted flange	Stage 1	Nm	-
			Stage 2	°	-
		with Ø 26 mm bolted flange	Stage 1	Nm	60
			Stage 2	°	90
BA35.10-P-1002-01A	Self-locking bolt, rear axle carrier rear rubber bushing to frame floor	-		Nm	-
		with Ø 24 mm bolted flange	Stage 1	Nm	-
			Stage 2	°	-
		with Ø 26 mm bolted flange	Stage 1	Nm	60
			Stage 2	°	90

 Torque strut

Number	Designation			Model 171


BA35.20-P-1001-03A	Self-locking nut, tension arm to rear axle carrier	M12	Nm	70
		M14	Nm	-
BA35.20-P-1002-03A	Self-locking nut, torque strut to wheel carrier	M12	Nm	70
		M16	Nm	-

 Torque strut

Number	Designation		Model 171


BA35.20-P-1003-05A	Self-locking nut, thrust arm to wheel carrier	Nm	50
		°	45

202 589 00 10 00

Retainer wrench

Ring wrench

129 589 01 03 00

140 589 01 62 00

Assembly attachment