ar3235b2050xa
Remove/install front stabilizer bar
Type ar · emne 32.35 · version 0102 · 2020-03-06
Gælder for: Model 368.0/1, 384.065 with engine 906, 924 (except 924.995), 926
Ikke tilgængelig på “da”; vises på Engelsk.
Placering
Funktionsgruppe 2 Chassis › 32 Affjedring › 32.35 Stabilisator — Serie 368 (modeller 0**, 1**) · Serie 384 (modeller 065) · Serie 906
EinPAS 17 Drivstreng/aksel › 17.50 Foraksel › 17.50.41 tværgående styrestang/styring/stabilisator — Serie 368 (modeller 0**, 1**) · Serie 384 (modeller 065) · Serie 906
Gælder også for motorer/gearkasser: 924 000, 924 910, 924 912, 924 913, 924 915, 924 916, 924 917, 924 919, 924 920, 924 922, 924 923, 924 925, 924 929, 924 930, 924 931, 924 932, 924 933, 924 934, 924 935, 924 936, 924 937, 924 941, 924 942, 924 971, 924 972, 924 981, 924 982, 924 985, 924 989, 924 990, 924 991, 924 993, 924 994, 924 996, 924 997, 924 998, 924 999, 926 ***
AR32.35-B-2050XA
| Remove/install front stabilizer bar
| 05.03.2020
|
Model
| 368.0/1, 384.065 with engine 906, 924 (except 924.995), 926
|
1
| Bearing cap
|
2
| Bolt
|
3
| Stabilizer
|
| Remove
|
|
|
1
| Lift the vehicle and support it
| Place the vehicle on a level, flat location. Chock the rear wheels to avoid the vehicle's unintentional rolling
|
|
2
| Loosen the bearing cap screws (1)
| .Bearing cap/split bearing
| *BA32.35-B-1003-02E
|
3
| Loosen the screws (2) and remove the anti-roll bar(3)
| Installation: Replace the screws (2) and nuts.
|
|
|
|
| Check the condition of the sleeves. Replace if necessary
|
|
|
|
| .Stabilizer on the longitudinal member's support
| *BA32.35-B-1005-02E
|
| Install
|
|
|
4
| Installation in reverse order
|
|
|
Number
| Designation
|
|
| Model 368, 382.123/154/155/176, 384.211, 634.0 (except 634.012/014)
|
BA32.35-B-1003-02E
| Bearing cap/split bearing
| M8
| Nm
| 25
|
|
|
| M10x1,5
| Nm
| 35
|
|
|
| M14x1.5
| Nm
| 150
|
|
|
| M16x1.5
| Nm
| 260
|
|
|
| M20x1.5
| Nm
| 460
|
|
|
| M24x2
| Nm
| 690
|
Number
| Designation
|
|
| Model 368, 382.123/154/155/176, 384.211, 634.0 (except 634.012/014)
|
BA32.35-B-1005-02E
| Stabilizer on the longitudinal member's support
| M12x1.5
| Nm
| 55
|
|
|
| M18x1.5
| Nm
| 330
|
