Transmission | 715.352 |
with code G2B (Transmission G 211-12/14.93-1.0) | |
Transmission | 715.360 |
with code G2C (Transmission G 230-12/11.7-0.78) | |
Transmission | 715.366/537/538/539 in model 800 |
Transmission | 715.371 |
with code G2E (Transmission G 281-12/14.93-1.0) | |
Transmission | 715.381 |
with code G2F (Transmission G 330-12/11.63-0.77) | |
Transmission | 715.508 |
with code G1H (Transmission G 230-16/14.2-0.83) | |
Transmission | 715.518 |
with code G1I (Transmission G 231-16/17.0-1.0) | |
Transmission | 715.523 |
with code G2D (Transmission G 280-16/11.7-0.69) | |
Transmission | 715.528 |
with code G1J (Transmission G 260-16/11.7-0.69) |
714 589 04 21 00
Setting gauge
366 589 00 21 05
Extension
001 589 53 21 00
Dial gage
715 589 00 21 00
Adjusting sleeve
1 | Preload tapered roller bearings (5) using adjusting sleeve (3) while turning gearwheel for constant speed gear 2 (6) several times. |
The tapered roller bearings (5) are sufficiently preloaded when the gearwheel for constant speed gear 2 (6) becomes difficult to turn. |
2 | Slacken off adjusting sleeve (3) slightly. |
3 | Turn gearwheel for constant speed gear 2 (6) several times while tapping the gearwheel for constant speed gear 2 (6) with plastic mallet. |
To release stresses. |
4 | Screw on adjusting sleeve (3) finger-tight again. |
W26.50-1113-01
5 | Attach dial indicator (1) to adjusting gauge (2). |
If the pin of the dial indicator (1) is too short, use the extension. |
6 | Attach adjusting gauge (2) so that it slides on adjusting sleeve (3). |
7 | Use dial indicator (1) on collar to measure main shaft (4). |
8 | Set dial indicator (1) to zero. |
9 | Use dial indicator (1) to measure dimension A on collar of tapered roller bearing (5). |
10 | Calculate thickness of shim (8) to be inserted: |
W26.50-1104-02
11 | Detach gearwheel for constant speed gear 2 (6) using a suitable pull-off device until end play of approx. 1.0 mm is achieved. |
12 | Fit calculated shim (8) and pressure plate (7) on collar of journal. |
13 | Fit adjusting sleeve (3) and tighten until the pressure plate (7) has pushed the tapered roller bearing back into its installation position. |
14 | Attach dial indicator (1) to adjusting gauge (2). |
15 | Attach adjusting gauge (2) so that it slides on adjusting sleeve (3). |
W26.50-1099-02
16 | Place dial indicator (1) onto ground surface of gearwheel for constant speed gear 2 (6) and turn gearwheel for constant speed gear 2 (6) approx. 20 times. |
17 | Set dial indicator (1) to zero. |
18 | Turn gearwheel for constant speed gear 2 (6) briefly to the right or left and, while simultaneously pushing up/down (arrows), read off bearing play on dial indicator (1). |
Do not use a screwdriver or tire iron to push the gearwheel for constant speed gear 2 (6) up and down. |
19 | If there is any deviation, correct using appropriate shim (8) and repeat measuring procedure. |
The objective is to have end play in the range of the lowest tolerance limit. |