ar2645w0014a

Remove/install power take-off shift fork

Type ar · emne 26.45 · version 0100 · 2013-05-24

Gælder for: TRANSMISSION 715.310/352/360/371/381/508/518/523/528/571 with power take-off 121

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 2 Chassis › 26 Manuel gearkasse › 26.45 Kraftudtag, kraftudtagsdrev

EinPAS 17 Drivstreng/aksel › 17.45 Kraftudtag › 17.45.52 Gearskifte

Gælder også for motorer/gearkasser: 715 310, 715 352, 715 360, 715 371, 715 381, 715 508, 715 518, 715 523, 715 528, 715 571

AR26.45-W-0014A

Remove/install power take-off shift fork

29.04.2013

TRANSMISSION

715.310/352/360/371/381/508/518/523/528/571

with power take-off 121

Remove/install power take-off shift fork

Shown on power take-off (PTO) 121-1c

1

Sliding sleeve

2

Screw plug

3

Spring

4

Shift fork

5

Sealing ring

6

Retaining ring

7

Pressure pin

8

Socket

9

Sealing ring

10

Shift rod

11

Support ring

12

Seal

13

Shift cylinder with solenoid valve

14

Screw

15

Washer

S2

Power take-off 1 indicator switch

W26.45-1338-06

Remove

1

Unscrew power take-off 1 indicator switch (S2) and remove sealing ring (5)

2

Take pressure pin (7) out of housing and remove retaining ring (6)

3

Remove shift cylinder with solenoid valve (13)

AR26.45-W-0007A

4

Unscrew screw plug (2) and remove spring (3)

5

Take out sliding sleeve (1) and shift fork (4)

Push back the shift fork (4) until the sliding sleeve (1) is free.

6

Remove bush (8)

Only if damaged or worn.

Install

7

Install bush (8) using suitable drift

Install the bush (8) such that the butt joint on the right is in the middle. Amount of recess approx. 0.5 mm.

8

Insert shift fork (4) in the housing

Push back the shift fork (4) until the sliding sleeve (1) can be installed.

9

Push on sliding sleeve (1) and insert the shift fork (4) in the radial groove of the sliding sleeve

The shift teeth of the sliding sleeve (1) must point toward the drive side.

10

Install shift cylinder with solenoid valve (13) together with shift rod (10)

AR26.45-W-0007A

Coat the slide surfaces of the shift rod (10) with lubricant.

Long-life grease

*BR00.45-Z-1001-06A

11

Insert spring (3) and screw in screw plug (2)

Screw in the screw plug (2) so that it is flush with the housing. Then continue turning until the plug is recessed by 0.3 to 1.0 mm.

12

Push retaining ring (6) onto pressure pin (7) and insert pressure pin (7) into housing

Coat the pressure pin (7) with lubricant.

Long-life grease

*BR00.45-Z-1001-06A

13

Screw in power take-off 1 indicator switch (S2) with sealing ring (5)

Replace sealing ring (5).

Indicator switch to shift housing

*BA26.45-N-1010-04A

Power take-off

Number

Designation

Transmission 715 with PTO 121

BA26.45-N-1010-04A

Indicator switch to shift housing

Nm

50

Repair materials

Number

Designation

Order number

BR00.45-Z-1001-06A

Long-life grease

A 000 989 63 51 11

Henviste dokumenter