ar2320w9430b

Remove/install rear engine power take-off.

Type ar · emne 23.20 · version 0108 · 2010-12-07

Gælder for: ENGINES 902.9 in MODEL 375.3, 950.5 /6, 952.5 /6, 953.6, 954.5, 957 with CODE (N52) Rear engine power take-off, output torque 600 Nm ENGINES 902.9 in MODEL 375.1, 970, 972, 974, 975, 976 with CODE (N52) Rear engine power take-off, output torque 600 Nm ENGINES 904.9, 906.9, 924.9, 926.9 in MODEL 958.0 with CODE (N52) Rear engine power take-off, output torque 600 Nm ENGINES 906.9 in MODEL 375.3, 950.5 /6, 952.5 /6, 953.6, 954.5, 957, 958.2 with CODE (N52) Rear engine power take-off, output torque 600 N

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 23 Specialindbygninger › 23.20 Motorudgang bagtil — Serie 375 (modeller 1**, 3**) · Serie 902 (modeller 9**) · Serie 904 (modeller 9**) · Serie 906 (modeller 9**) · Serie 950 (modeller 5**, 6**) · Serie 952 (modeller 5**, 6**) · Serie 953 (modeller 6**) · Serie 954 (modeller 5**) · Serie 957 · Serie 958 (modeller 0**, 2**) · Serie 970 · Serie 972 · Serie 974 · Serie 975 · Serie 976

EinPAS 17 Drivstreng/aksel › 17.45 Kraftudtag › 17.45.30 Kraftudtag komplet — Serie 375 (modeller 1**, 3**) · Serie 902 (modeller 9**) · Serie 904 (modeller 9**) · Serie 906 (modeller 9**) · Serie 950 (modeller 5**, 6**) · Serie 952 (modeller 5**, 6**) · Serie 953 (modeller 6**) · Serie 954 (modeller 5**) · Serie 957 · Serie 958 (modeller 0**, 2**) · Serie 970 · Serie 972 · Serie 974 · Serie 975 · Serie 976

Gælder også for motorer/gearkasser: 924 9**, 925 9**, 926 9**

AR23.20-W-9430B

Remove/install rear engine power take-off.

23.11.10

ENGINES 902.9 in MODEL 375.3, 950.5 /6, 952.5 /6, 953.6, 954.5, 957 with CODE (N52) Rear engine power take-off, output torque 600 Nm

ENGINES 902.9 in MODEL 375.1, 970, 972, 974, 975, 976 with CODE (N52) Rear engine power take-off, output torque 600 Nm

ENGINES 904.9, 906.9, 924.9, 926.9 in MODEL 958.0 with CODE (N52) Rear engine power take-off, output torque 600 Nm

ENGINES 906.9 in MODEL 375.3, 950.5 /6, 952.5 /6, 953.6, 954.5, 957, 958.2 with CODE (N52) Rear engine power take-off, output torque 600 Nm

ENGINES 906.9 in MODEL 970, 972, 974, 975, 976 with CODE (N52) Rear engine power take-off, output torque 600 Nm

ENGINES 925.9 in MODEL 970, 972, 974 with CODE (N52) Rear engine power take-off, output torque 600 Nm

ENGINES 926.9 in MODEL 950.5 /6, 952.5 /6, 953.6, 954.5, 957, 958.2 with CODE (N52) Rear engine power take-off, output torque 600 Nm

Remove/install rear engine power take-off.

W23.20-1000-10

1 Rear engine power take-off

2 Sealing ring

3 Drive flange

Remove/install

Danger!

Risk of injury caused by body parts being pinched or crushed as cab is tilted

Ensure that no one is within tilting range of cab as it is being tilted. Always tilt cab all the way to end position and secure with safety strut.

AS60.80-Z-0001-01A

1

Tilt cab

Notes on tilting the cab

AH60.80-N-0003-01A

2

Remove soundproofing on frame at top right and below

3

Disconnect propeller shaft from drive flange (3)

Only when an auxiliary unit is installed.

*BA23.20-N-1004-01C

Danger!

Risk of injury to skin and eyes caused by handling hot or glowing objects.

Wear safety gloves, protective clothing and safety glasses, if necessary.

AS00.00-Z-0002-01A

4

Remove rear engine power take-off (1) at timing case

Slightly heat up the outside of the timing case around the rear engine power take-off (1) using a hot air blower.

Installation: Screw in bolts with thread M81.25 as an assembly aid into the timing case. When pressing in the rear engine power take-off (1), observe the hole pattern.

*BA23.20-N-1002-01C

5

Remove sealing ring (2)

6

Install in the reverse order

Rear engine power take-off

Number

Designation

Engine 900.9, 902.9, 904.9, 906.9, 924.9, 925.9, 926.9 with code N52

BA23.20-N-1002-01C

Bolt, engine power take-off to timing case

Nm

25

BA23.20-N-1004-01C

Bolt, propeller shaft to drive flange

Nm

25

Henviste dokumenter