ar2210w1160b

Remove/install rear engine mount

Type ar · emne 22.10 · version 0103 · 2010-11-25

Gælder for: ENGINE 902.9 in MODEL 950.5 /6, 952.5 /6, 953.6, 954.5 ENGINE 925.9 in MODEL 970, 972, 974 ENGINE 926.9 in MODEL 950.5 /6, 952.5 /6, 953.6, 954.5 ENGINE 926.9 in MODEL 958.0

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 22 Aggregatophæng › 22.10 Aggregatleje, aggregatholder — Serie 902 (modeller 9**) · Serie 950 (modeller 5**, 6**) · Serie 952 (modeller 5**, 6**) · Serie 953 (modeller 6**) · Serie 954 (modeller 5**) · Serie 958 (modeller 0**) · Serie 970 · Serie 972 · Serie 974

EinPAS 15 Motor › 15.15 forbrændingsmotor komplet/motorblok/krumtapdrev › 15.15.20 motorophæng — Serie 902 (modeller 9**) · Serie 950 (modeller 5**, 6**) · Serie 952 (modeller 5**, 6**) · Serie 953 (modeller 6**) · Serie 954 (modeller 5**) · Serie 958 (modeller 0**) · Serie 970 · Serie 972 · Serie 974

Gælder også for motorer/gearkasser: 925 9**, 926 9**

AR22.10-W-1160B

Remove/install rear engine mount

23.11.10

ENGINE 902.9 in MODEL 950.5 /6, 952.5 /6, 953.6, 954.5

ENGINE 925.9 in MODEL 970, 972, 974

ENGINE 926.9 in MODEL 950.5 /6, 952.5 /6, 953.6, 954.5

ENGINE 926.9 in MODEL 958.0

Remove/install rear engine mount

W22.10-1015-08

Left side of vehicle

1 Bolts

2 Engine mount (left rear)

5 Bolts

6 Screw

3 Battery wiring harness

4 Transmission carrier (left)

Remove/install rear engine mount

W22.10-1016-08

Right side of vehicle

7 Bolts

8 Engine mount (right rear)

11 Bolts

12 Screw

9 Wiring harness

10 Transmission carrier (right)

Remove/install

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

1

Support transmission from below using a transmission jack

2

Unscrew bolts (6, 12) on the transmission carriers (4, 10)

*BA22.10-N-1002-01B

3

Lift transmission until the transmission carriers (4, 10) are a distance of approx. 1 cm from the engine mounts (2, 8)

4

Detach cable tie from battery wiring harness (3) on left engine mount (2) and pull battery wiring harness (3) slightly to one side

Installation: Install new cable ties.

5

Loosen AdBlue tank from the mounting consoles and pull forward approx. 4 cm

Only on vehicles on which the mounting of the left engine mount (2) is not accessible for reason of the AdBlue tank positioned in front of it.

6

Detach left engine mount (2) from longitudinal frame member

Installation: Align engine mount (2); for this purpose, position the engine mount (2) from inside on the longitudinal frame member, screw in the four bolts (1) first and then screw in bolt (6) slightly. After this, tighten all bolts (1, 6).

*BA22.10-N-1005-01B

7

Detach cable tie from wiring harness (9) on right engine mount (8) and pull wiring harness (9) slightly to one side

Installation: Install new cable ties.

8

Detach right engine mount (8) from longitudinal frame member

Installation: Align engine mount (8); for this purpose position the engine mount (8) from inside on the longitudinal frame member, screw in the four bolts (7) first and then screw in bolt (12) slightly. After this, tighten all bolts (7, 12).

*BA22.10-N-1005-01B

9

Install in the reverse order

Engine mounts, engine supports

Number

Designation

Engine
900.9, 902.9, 904.9 906.9, 924.9, 925.9, 926.9
in model
374, 375, 673, 674, 676, 950, 952, 953, 954, 958, 970, 972, 974, 975, 976

BA22.10-N-1002-01B

Bolt from engine carrier to engine mount

Nm

225

BA22.10-N-1005-01B

Bolt from engine mount to frame

Nm

160

Henviste dokumenter