ar2040p6800t

Remove/install fan shroud

Type ar · emne 20.40 · version 0207 · 2010-01-13

Gælder for: ENGINES 646.951 in MODEL 211.004 ENGINES 646.961 in MODELS 211.006 /206 /606 ENGINES 647.961 in MODEL 211.016 /216 /616 ENGINES 271.941 in MODELS 211.042 /242 ENGINES 648.961 in MODEL 211.023 /026 /223 /226 ENGINES 646.8 in MODEL 211 ENGINES 271.956 in MODEL 211.041 /241

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 20 Motorkøling › 20.40 Ventilator, ventilatorkobling — Serie 211 · Serie 646 (modeller 8**, 951, 961) · Serie 647 (modeller 961) · Serie 648 (modeller 961)

EinPAS 15 Motor › 15.25 Motorkølesystem › 15.25.45 ventilator/ventilatorkobling/ventilatordrev — Serie 211 · Serie 646 (modeller 8**, 951, 961) · Serie 647 (modeller 961) · Serie 648 (modeller 961)

Gælder også for motorer/gearkasser: 271 941, 271 956

AR20.40-P-6800T

Remove/install fan shroud

17.12.09

ENGINES 646.951 in MODEL 211.004

ENGINES 646.961 in MODELS 211.006 /206 /606

ENGINES 647.961 in MODEL 211.016 /216 /616

ENGINES 271.941 in MODELS 211.042 /242

ENGINES 648.961 in MODEL 211.023 /026 /223 /226

ENGINES 646.8 in MODEL 211

ENGINES 271.956 in MODEL 211.041 /241

Remove/install fan shroud

P20.40-2044-09

Shown on model 211.006

1 Rubber seal

2 Radiator crossmember

7 Bracket

8 Connector

9 Retaining lug

3 Bolts

4 Flat spring

5 Fan shroud

6 Coolant hose

Remove/install

Danger!

Risk of injury caused by fingers being pinched or crushed when removing, installing or aligning hoods, doors, trunk lids, liftgates or sliding roof

Keep body parts and limbs well clear of moving parts.

AS00.00-Z-0011-01A

1

Open engine hood

AR88.40-P-1000T

2

Remove engine intake air duct upstream of air filter

Model 211.041 /042 /241 /242

3

Remove cylinder head cover trim

Engine 646.8/9, 647.9

AR01.20-P-5014-02A

Engine 648.9

AR01.20-P-5014-02C

Bolt, cylinder head cover trim to cylinder head

*BA01.20-P-1002-01G

Bolt, cover to charge air manifold

*BA01.20-P-1003-01G

4

Remove the rubber seal (1) in upper frame crossmember (2) region

5

Remove screws (3) and

Fold radiator crossmember (2) forwards

Screw for center reinforcement to outer reinforcement

*BA62.30-P-1008-02A

Screw for center reinforcement to catch hook reinforcement

*BA62.30-P-1009-02A

6

Pull off flat springs (4) on upper side of fan shroud (5)

7

Loosen coolant hose (6) from brackets (7) at fan shroud (5)

8

Remove the plug (8) from the fan shroud (5)

9

Take out the fan shroud (5) in the upward direction.

Installation: Insert retaining lugs for fan shroud (5) into mounts at radiator (9).

10

Install in the reverse order

11

Check sensor setting of Distronic

Vehicles with Distronic (DTR) code 219

AR30.30-P-1000R

Crankcase ventilation, cylinder head cover

Number

Designation

Engine
646.8

Engine
646.951/961,
647.961

Engine
648

BA01.20-P-1002-01G

Bolt, cylinder head cover trim to cylinder head

Nm

-

9

9

BA01.20-P-1003-01G

Bolt, cover to charge air manifold.

Nm

-

9

9

Front end assembly with front reinforcement

Number

Designation

Model
211

BA62.30-P-1008-02A

Bolt, center reinforcement to outer reinforcement

Nm

10

BA62.30-P-1009-02A

Bolt, center reinforcement to arrester hook reinforcement

Nm

10

Henviste dokumenter