ar1322p1202b

Remove, install poly V-belt

Type ar · emne 13.22 · version 0121 · 2006-05-02

Gælder for: ENGINE 112.945 in MODEL 463.232 /233 /244 /209 /245 /250 ENGINE 112 in MODEL 129, 163 ENGINE 113 (except 113.981 /965) in MODEL 202, 208, 129, 210, 163 ENGINE 113.962 in MODEL 463.247 /240 /241 /206 /249 /248 /254 ENGINE 113.982 in MODEL 463.246 /243

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 13 Kompressor, remtræk › 13.22 Enkeltremstræk — Serie 129 · Serie 163 · Serie 202 · Serie 208 · Serie 210 · Serie 463 (modeller 206, 209, 232, 233, 240, 241, 243, 244, 245, 246, 247, 248, 249, 250, 254)

EinPAS 15 Motor › 15.18 Remtræk › 15.18.30 rem/remskive/spændeanordning/styrerulle — Serie 129 · Serie 163 · Serie 202 · Serie 208 · Serie 210 · Serie 463 (modeller 206, 209, 232, 233, 240, 241, 243, 244, 245, 246, 247, 248, 249, 250, 254)

Gælder også for motorer/gearkasser: 112 ***, 112 945, 113 940, 113 941, 113 942, 113 943, 113 944, 113 948, 113 960, 113 961, 113 962, 113 963, 113 964, 113 966, 113 967, 113 968, 113 969, 113 971, 113 980, 113 982, 113 984, 113 985, 113 986, 113 987, 113 988, 113 989, 113 990, 113 991, 113 992, 113 993, 113 994, 113 995

AR13.22-P-1202B

Remove, install poly V-belt

12.4.06

ENGINE 112.945 in MODEL 463.232 /233 /244 /209 /245 /250

ENGINE 112 in MODEL 129, 163

ENGINE 113 (except 113.981 /965) in MODEL 202, 208, 129, 210, 163

ENGINE 113.962 in MODEL 463.247 /240 /241 /206 /249 /248 /254

ENGINE 113.982 in MODEL 463.246 /243

Remove, install poly V-belt

P13.22-0236-06

Shown on engine 112

1 Viscous fan

2 Fan shroud

3 Poly-V-belt

4 Stud bolt

5 Tensioning pulley

Remove

1

Remove viscous fan (1)

Right-hand thread!

AR20.40-P-5660C

2

Remove fan shroud (2).

Model 129, 202, 208, 210.

On model 163 unscrew bolts at bottom of fan shroud.

Model 463

AR20.40-P-6800V

3

Loosen and remove the poly-V-belt (3)

For this step, swivel stud bolt (4) at tensioning pulley (5) in anti-clockwise direction Lock the tension pulley with a pin or mandrel (diameter 5mm).

External torx set

*001589760900

Check

4

Inspect belt pulley sections and tensioning device for damage and dirt

5

Check poly-V-belt (3)

Check poly-V-belt in visible area for wear

Engine 112, 113 (except 112.942 /945 /970, 113.942 /962 /965 /981 /982)

AP13.22-P-1352Z

Engine 112.945, 113.962 /982 in model 463

AP13.22-P-1351GA

Engine 112.942 /970, 113.942 /965 /981 in model 163

AP13.22-P-1351GH

Install

6

Fit on poly-V-belt (3), then clamp

Do not use belt wax or any similar products.

Proceed by the numbered sequence of the respective belt routing pattern, starting with the tension pulley:

Layout diagram of poly-V-belt

AR13.22-P-3902-02B

7

Install fan shroud (2)

Model 129, 163, 202, 208, 210.

Model 463 with engine 112, 113

AR20.40-P-6800V

8

Install the viscous fan (1)

Right-hand thread!

AR20.40-P-5660C

Remove, install poly V-belt

001 589 76 09 00

External Torx set

Henviste dokumenter