ar0715b1628a

Remove/install MR/PLD control unit

Type ar · emne 07.15 · version 0102 · 2020-02-04

Gælder for: Engine 904 in model 688.2 Engine 904 in model 693.0 Engine 904, 906, 924, 926 (except 926.942) in model 368, 382.1 (except 382.171/176), 384.2, 685.282/284/289/290, 688.2

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 07 Blandingstilberedning › 07.15 Dieselindsprøjtningssystem (PLD), motorregulering (MR) — Serie 368 · Serie 382 (modeller 111, 123, 134, 135, 143, 153, 154, 155, 156, 157, 158, 175, 177, 178, 180, 181, 182, 184, 185, 186, 187, 188, 189, 190) · Serie 384 (modeller 2**) · Serie 685 (modeller 282, 284, 289, 290) · Serie 688 (modeller 2**) · Serie 693 (modeller 0**) · Serie 904 · Serie 906

EinPAS 15 Motor › 15.45 Motorstyring › 15.45.11 Styreenhed/relæ — Serie 368 · Serie 382 (modeller 111, 123, 134, 135, 143, 153, 154, 155, 156, 157, 158, 175, 177, 178, 180, 181, 182, 184, 185, 186, 187, 188, 189, 190) · Serie 384 (modeller 2**) · Serie 685 (modeller 282, 284, 289, 290) · Serie 688 (modeller 2**) · Serie 693 (modeller 0**) · Serie 904 · Serie 906

Gælder også for motorer/gearkasser: 924 ***, 926 000, 926 900, 926 910, 926 911, 926 912, 926 913, 926 914, 926 915, 926 916, 926 917, 926 918, 926 919, 926 920, 926 921, 926 924, 926 925, 926 926, 926 927, 926 928, 926 929, 926 930, 926 932, 926 933, 926 934, 926 935, 926 937, 926 938, 926 941, 926 945, 926 946, 926 947, 926 948, 926 949, 926 950, 926 956, 926 959, 926 960, 926 961, 926 969, 926 970, 926 971, 926 972, 926 973, 926 974, 926 975, 926 976, 926 985, 926 986, 926 987, 926 988, 926 989, 926 990, 926 991, 926 992, 926 993, 926 994, 926 995, 926 996, 926 997, 926 998, 926 999

AR07.15-B-1628A

Remove/install MR/PLD control unit

03.02.2020

Engine

904 in model 688.2

Engine

904 in model 693.0

Engine

904, 906, 924, 926 (except 926.942) in model 368, 382.1 (except 382.171/176), 384.2, 685.282/284/289/290, 688.2

Remove/install MR/PLD control unit

1

Side trim

2

Bolts

3

Connector of vehicle electric wires

4

Connector of engine electric wires

5

Support of engine electric cables

6

Rubber pad

A6

Control unit (PLD)

B07.15-1080-06

Remove/install

Warning

Risk of injury caused by body parts being pinched or crushed as cab is tilted

Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut.

AS60.80-Z-0001-01A

1.1

Tilt the cabin

.

.

AR60.80-B-0010A

.

AR60.80-B-0010C

Warning

Risk of injury caused by pinching and crushing when opening and closing engine hood

No one should be within the swivel range of the engine hood as it is being opened or closed. Always open engine hood all the way to the end position until this engages in the front locks.

AS88.40-Z-0001-01A

1.2

Tilt the engine hood

.

.

AR88.40-B-1000A

1.3

Open the engine access cover

For buses and special-purpose vehicles, the access to carry out maintenance and repair jobs vary according to body type/make.

Refer to the body makers instructions.

2

Remove side trim (1)

3

Disconnect the vehicle electric cables (3) at the operating unit (A6)

Separate, connect plug connection of vehicle wiring harness at MR/PLD control module
.

AR07.15-B-1628-01A

When disconnecting or connecting the electric wires, the vehicle contact switch must be in the OFF position.

4

Disconnect the engine electric cables (4) at the operating unit (A6)


.

AR07.15-B-1628-02A

When disconnecting or connecting the electric wires, the vehicle contact switch must be in the OFF position.

5

Unscrew the bolts (2) ans remove the cable support (5), rubber cushions (6) and the operating unit (A6)

Installation: Observe the assembly position of the cushions (6) and cable support (5).

.Engine block control unit

*BA07.15-B-1002-01A

6

Install in reverse order

Diesel injection system with injection unit (MR/PLD)

Number

Designation

Engine 904.9, 906.9, 924.9, 926.9

BA07.15-B-1002-01A

Engine block control unit

Nm

15

Henviste dokumenter