ar0708p7008ew

Remove/install injection system control unit

Type ar · emne 07.08 · version 0101 · 2010-01-12

Gælder for: ENGINE 272, 273 (except 272.983) in MODEL 212

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 07 Blandingstilberedning › 07.08 Styreenheder — Serie 212

EinPAS 15 Motor › 15.45 Motorstyring › 15.45.11 Styreenhed/relæ — Serie 212

Gælder også for motorer/gearkasser: 272 911, 272 920, 272 921, 272 922, 272 923, 272 924, 272 939, 272 940, 272 941, 272 942, 272 943, 272 944, 272 945, 272 946, 272 947, 272 948, 272 949, 272 952, 272 960, 272 961, 272 963, 272 964, 272 965, 272 966, 272 967, 272 968, 272 969, 272 970, 272 971, 272 972, 272 973, 272 974, 272 975, 272 977, 272 978, 272 979, 272 980, 272 982, 272 984, 272 985, 272 988, 272 991, 273 ***

AR07.08-P-7008EW

Remove/install injection system control unit

2.12.09

ENGINE 272, 273 (except 272.983) in MODEL 212

Remove/install injection system control unit

P07.08-2097-08

1a Right control unit bracket

1b Left control unit bracket

N3/10 ME-SFI [ME] control unit

2 Ball head support

Remove/install

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

1

Read out transfer variant coding of ME-SFI [ME] control unit (N3/10) using STAR DIAGNOSIS

When replacing ME-SFI [ME] control unit (N3/10).

Connect up STAR DIAGNOSIS and read data from the ME-SFI [ME] control unit (N3/10) into STAR DIAGNOSIS.

Installation: Transfer stored data to the new ME-SFI [ME] control unit (N3/10).

2

Switch off ignition

3

Remove air filter housing

AR09.10-P-1150EWS

4

Move shift interlocks for electrical connectors on the ME-SFI [ME] control unit (N3/10) in the direction of the arrows and disconnect electrical connectors from the ME-SFI [ME] control unit (N3/10)

5

Pull ME-SFI [ME] control unit (N3/10) up and out of control unit brackets (1a, 1b)

6

Detach ball-type support braces (2) from ME-SFI [ME] control unit (N3/10)

When replacing the ME-SFI [ME] control unit (N3/10)

*BA07.08-P-1001-01A

7

Remove control unit brackets (1a, 1b) from resonance intake manifold as needed

*BA07.08-P-1002-01A

8

Install in the reverse order

9

Perform sensor rotor adaptation using STAR DIAGNOSIS

When replacing ME-SFI [ME] control unit (N3/10).

Menu guidance:

Engine control module

Adaptations

Learning processes

10

Release transport protection on ME-SFI [ME] control unit (N3/10)

When replacing ME-SFI [ME] control unit (N3/10).

11

Personalize and activate ME-SFI [ME] control unit (N3/10)

When replacing ME-SFI [ME] control unit (N3/10).

Danger!

Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running

Secure vehicle to prevent it from moving by itself.
Wear closed and snug-fitting work clothes.
Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

12

Carry out engine test run

When replacing ME-SFI [ME] control unit (N3/10).

Control unit

Number

Designation

Engine 272

Engine 273

BA07.08-P-1001-01A

Ball head support to control unit

Nm

4

4

BA07.08-P-1002-01A

Bolt, control unit bracket to resonance intake manifold

Nm

8

8

Henviste dokumenter