1 | Temperature sensor |
2 | Retaining clamp |
3 | Electrical connector |
4 | Electrical wiring harness |
D07.04-A012-06
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Warning | Risk of burn injuries, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust. | Wear protective clothing and safety glasses. Use the extraction system. Move people out of the hazard area. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
| Remove/install | ||
1 | Raise vehicle. | ||
Topical note | Special instructions for lifting and supporting vehicle | ||
2 | Remove lower engine compartment lining | If installed. | |
3 | Disconnect electrical connector (3). | ||
4 | Remove the electrical wiring harness (4). | Installation: Check retaining clamps (2) for damage. | |
If necessary, | |||
| |||
Replace damaged retaining clips (2). | |||
5 | Unscrew temperature sensor (1). | ||
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
Installation: Coat thread of temperature sensor (1) with heat-resistant lubricating paste. | |||
Paste, hot lubrication 1 kg, DBL 6879.20 | |||
Temperature sensor on diesel particulate filter | |||
Box wrench bit | |||
6 | Install in the reverse order. | ||
7 | Read out the fault memory using the diagnostic unit. | If temperature sensor (1) was replaced. | |
| Connect/disconnect diagnostic unit | ||
If existing faults are shown: | |||
| |||
Erase the fault memory. | |||
| Check | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
8 | Check for leaktightness when engine is running. | Visual inspection only. |
000 589 69 03 00
Box wrench bit
Henviste dokumenter
- ad0000d200006ts
- ah0000p001501cw Oplysning om beregning af tilspændingsmoment ved anvendelse af indstiksværktøj eller påsætningsværktøj af forskellig længde
- ah0000p500001a Oplysninger om forebyggelse af skader på grund af snavs og fremmedlegemer
- ah0060n010001ts Bemærkning til hævning og opklodsning
- ah5400p000101a Oplysninger med henblik på at undgå skader på elektroniske komponenter på grund af elektrostatisk afladning
- ar0060d100004ts
- ar6120d1105ts
- as0000z000201a Fare for personskade på hud og øjne ved håndtering af varme eller glødende genstande
- as0000z000501a Fare for ulykke ved automatisk igangsætning når motoren kører. Fare for personskade på grund af knusning og forbrænding, hvis der arbejdes mens motoren startes eller kører
- as0000z001001a Livsfare, hvis køretøjet glider ned fra eller tipper på liften.
- as4900z000101a Forbrændings-, kvælnings- og forgiftningsfare ved arbejde på udstødningssystemet og dermed forbundne komponenter. Kvælningsfare og fare for forgiftning ved indånding af gasformede og faste komponenter i forbrændingsgassen. Fare for