B42.10-0016-01
B42.60-0012-01
B42.60-0008-01
Model 382.175/176/184/186, 634.001 |
One-chamber air dryer |
Model 382.180/181/185/188/189 |
Seta - | Granulate cartridge |
OF Bus |
1 - | Granulate cartridge |
B42.60-0009-01
B42.60-0010-01
B42.60-0011-01
Two-chamber air dryer - Wabco |
2 | Sealing rings |
3 | Housing |
4 | Spring |
5 | Granulate cartridge |
6 | Filter element |
7 | Spring |
8 | Filter cover |
9 | Retaining ring |
| Remove | ||
1 | Depressurize air drier pneumatic system | ||
2 | Remove the granulate cartridge (1) | Only in model with Code (B66) one-chamber pneumatic dryer. | |
Discard the granulate cartridge ecologically and follow the same legislation for the oil filter. | |||
Cartridge wrench | |||
3 | Release the fixing entrance rail nuts | Follow working steps 3, 4, 5, 6 only in models with Code (B67) two-chamber pneumatic dryer. | |
First release the nuts on the shortest side of the entrance rail. | |||
4 | Remove the fixing entrance rail, together with the housings (3), springs (4) and granulate cartridges (5) | Cartridge wrench | |
5 | Pushing the filter cover (8) up and compress the retaining ring (9) | ||
6 | Remove the filter cover (8), the spring (7) and the filter element (6) | Installation: Slightly oil the sliding surface of the end cover (8), mount the filter element (6) with the spring (7) and secure it with the retaining ring (9). | |
Observe that the retaining ring is fully locked into the slot. | |||
If necessary, replace the filter element. | |||
| Clean | ||
7 | Clean the cartridge seat in the housing | ||
8 | Clean the housings (3), the springs (4, 7), the filter cover (8) and the filter element (6) | Only in model with Code (B67) two-chamber pneumatic dryer. | |
Clean the filter element chamber. | |||
Using a suitable solvent and dry using compressed air. | |||
Lubricate | |||
9 | Slightly grease the cartridge gasket and sealing thread | Check the gasket and the sealing thread for damage. | |
10 | Grease the sealing rings (2) | ||
| Install | ||
11.1 | Install the new cartridge | Only in model with Code (B66) one-chamber pneumatic dryer. | |
The cartridge should be manually mounted on the air drier housing until the gasket leans against the housing, then apply a new torque (about half a turn) using the cartridge wrench. | |||
Excess torque may damage the cartridge. | |||
Cartridge wrench | |||
11.2 | Install the new granulate cartridges (5) and fix the housings (3) using the entrance rail, alternately tightening the nuts | Only in model with CODE (B67) two-chamber pneumatic dryer. | |
.Dryer and pressure regulator | |||
Cartridge wrench | |||
12 | Pressurize the air drier pneumatic system and check for leak tightness | If leaks are observed, depressurize the system before retightening the air drier. | |
13 | Write down the granulate cartridge replacement in the maintenance manual |
Pneumatic brake system |
Number | Designation | Model 368, 382, 384.2/3, 386.0, 388.0, 660, 682, 688, 693, 694, 695, 696 | ||
BA42.60-B-1001-04A | Dryer and pressure regulator | Feeding hollow bolt - Wabco/Knorr | Nm | 50 |
Protection valve fastening bolts - Wabco/Knorr | Nm | 20...24 | ||
Bolt that fastens the air dryer to the support - Wabco/Knorr | Nm | 25...30 | ||
Air pressure regulator cover bolt - Wabco | Nm | 5 | ||
Adjustment bolt nut - Wabco | Nm | 5 | ||
Diaphragm fastening nut - Wabco | Nm | 20...25 | ||
tires filling valve body - Wabco | Nm | 35...43 | ||
Nuts that fasten the housing to the supporting nuts - Wabco | Nm | 25 |
655 589 00 61 00
Cartridge wrench