Fault code list for drive control (FR) control unit

AD00.19-N-9009EA

Fault code list for drive control (FR) control unit

11.1.08

Fault code

Fault code description

0110

No or incorrect CAN message from control unit ABS anti-lock braking system

0111

Measured value of control module GS Gear control is implausible.

0112

No or incorrect CAN message from control unit KS clutch control

0113

No or incorrect CAN message from control unit RS Retarder control

0114

No or incorrect CAN message from control unit INS Instrument

0115

No or incorrect CAN message from control unit PSM Parameterizable Special Module

0117

Measured value of control module WSK torque converter-clutch is implausible.

0119

Measured value of control module KWS Articulation angle control is implausible.

0180

Measured value of control module ART autonomous intelligent cruise control is implausible.

0201

Engine CAN to MR engine control in single-wire mode

0202

No or incorrect CAN message from control unit MR engine control

0203

Engine CAN to MR engine control interrupted

0306

Engine CAN to FLA flame starting system interrupted

0416

High speed CAN bus has failed for more than 100 ms.

0418

High speed CAN bus has failed.

0501

Transmission CAN databus in single-wire mode

0508

Transmission CAN databus is not supplying any data.

0584

Impairment of function 'KR'

0681

Automatic gear selection failed

0682

Automatic gear selection in emergency mode

0783

Error during data scanning

1120

Connection 'D+' has Short circuit to positive.

1125

Connection 'D+' at pin X4 18/13 is implausible or has Open circuit or Short circuit to ground.

1223

Clutch pedal switch 1 at pin X1 18/1 has Open circuit or is incorrectly adjusted.

1421

Brake light switch has Open circuit or is incorrectly adjusted.

1423

Brake light switch at pin X1 18/11 has short circuit.

1523

Cruise control Temposet switch is faulty.

1524

Cruise control Temposet switch is faulty.

1526

Input 'Quit' of cruise control switch is open.

1623

Clutch pedal switches 1 and 2: incorrect adjustment or switches sticking

1723

Neutral position switch at pin X4 18/16 is faulty or stuck.

1923

Splitter switch at pins X2 18/11 and X2 18/12 has Open circuit or is faulty.

2023

Engine brake switch of "Engine control / continuous brake" operating lever faulty

2120

Output X1 18/13 has Short circuit to positive.

2122

Output X1 18/13 has Short circuit to ground.

2520

Switch group 1/4 has Short circuit to positive.

2522

Switch group 1/4 has Short circuit to ground.

2620

Switch group 2/3 has Short circuit to positive.

2622

Switch group 2/3 has Short circuit to ground.

2720

The oil level switch of the automatic engine oil replenishing M2 has Short circuit to positive.

2823

Double operation of ART pushbuttons

2923

Shift control module implausible

2927

The shift control unit GS Gear control is stuck.

2928

The shift control module GS Gear control is faulty.

2929

Button 'Automatic/Manual' of shift control unit GS Gear control is stuck.

3021

Circuit 30 has Open circuit.

3031

Terminal 30 overvoltage

3032

Terminal 30 undervoltage

3130

Coolant level switch X3 15/11 or air filter monitoring sensor X3 15/1 faulty, voltage supply X3 15/13 has Open circuit or Short circuit to positive or Short circuit to ground.

3233

Air filter monitoring sensor faulty

3236

Soiling limit of air cleaner is reached.

3330

Outside air temperature sensor Open circuit/Short circuit to positive/Short circuit to ground

3430

Clutch travel sensor has Open circuit, Short circuit to ground or Short circuit to positive.

3533

Coolant level switch is faulty.

3634

Maximum wear of clutch lining is reached.

3635

Clutch position sensor not within permissible range

4141

'Transmission input speed' signal is implausible.

4145

Transmission input speed sensor Open circuit/Short circuit to positive/Short circuit to ground

4341

Invalid speed signal

4345

The vehicle speed signal has Open circuit or Short circuit to ground or Short circuit to positive.

4440

The first branch of the foot throttle actuator has Open circuit or Short circuit to positive or Short circuit to ground.

4540

The second branch of the foot throttle actuator has Open circuit or Short circuit to positive or Short circuit to ground.

4641

Foot throttle actuator faulty

4642

Foot throttle actuator does not reach idle throttle stop.

4643

Foot throttle actuator not within learned range

4644

Foot throttle actuator stiff in operation

5052

Solenoid valve 1 at pin X3 15/4 has Short circuit to ground.

5053

Solenoid valve 1 at pin X3 15/4 has Short circuit to positive.

5054

Solenoid valve 1 at pin X3 15/4 has Open circuit.

5152

Solenoid valve 2 at pin X3 15/7 has Short circuit to ground.

5153

Solenoid valve 2 at pin X3 15/7 has Short circuit to positive.

5154

Solenoid valve 2 at pin X3 15/7 has Open circuit.

5252

Common ground cable of solenoid valves Constant throttle and Engine brake has Short circuit to ground.

5253

Common ground cable of solenoid valves Constant throttle and Engine brake has Short circuit to positive.

5352

'Splitter 1' solenoid valve has Short circuit to ground.

5353

'Splitter 1' solenoid valve has Short circuit to positive.

5354

'Splitter 1' solenoid valve has Open circuit.

5452

'Splitter 2' solenoid valve has Short circuit to ground.

5453

'Splitter 2' solenoid valve has Short circuit to positive.

5454

'Splitter 2' solenoid valve has Open circuit.

5552

Common ground cable of solenoid valves Y29 and Y30 has Short circuit to ground.

5553

Common ground cable of solenoid valves Y29 and Y30 has Short circuit to positive.

5652

'Brake light actuation' output has Short circuit to ground.

5653

'Brake light actuation' output has Short circuit to positive.

5654

'Brake light actuation' output has Open circuit.

5752

'Reversing light actuation' output has Short circuit to ground.

5753

'Reversing light actuation' output has Short circuit to positive.

5754

'Reversing light actuation' output has Open circuit.

5852

'Actuation of D+' output has Short circuit to ground.

5853

'Actuation of D+' output has Short circuit to positive.

5854

'Actuation of D+' output has Open circuit.

5952

Actuation of automatic engine oil replenishing has Short circuit to ground.

5953

Actuation of automatic engine oil replenishing has Short circuit to positive.

5954

Actuation of automatic engine oil replenishing has Open circuit.

6262

Control module has an internal error.

6265

Control module has an internal error.

6361

Control unit is in bootloader mode.

6365

Control module has an internal error.

7060

Parameterization error or internal error Parameter block 000 is implausible.

or

Parameterization error or internal error Parameter block 009 is implausible.

or

Parameterization error or internal error Parameter block 010 is implausible.

or

Parameterization error or internal error Parameter block 011 is implausible.

or

Parameterization error or internal error Parameter block 012 is implausible.

or

Parameterization error or internal error Parameter block 013 is implausible.

or

Parameterization error or internal error Parameter block 014 is implausible.

or

Parameterization error or internal error Parameter block 015 is implausible.

or

Parameterization error or internal error Parameter block 019 is implausible.

or

Parameterization error or internal error Parameter block 020 is implausible.

or

Parameterization error or internal error Parameter block 021 is implausible.

or

Parameterization error or internal error Parameter block 022 is implausible.

or

Parameterization error or internal error Parameter block 023 is implausible.

or

Parameterization error or internal error Parameter block 024 is implausible.

or

Parameterization error or internal error Parameter block 029 is implausible.

or

Parameterization error or internal error Parameter block 030 is implausible.

or

Parameterization error or internal error Parameter block 031 is implausible.

or

Parameterization error or internal error Parameter block 032 is implausible.

or

Parameterization error or internal error Parameter block 039 is implausible.

or

Parameterization error or internal error Parameter block 040 is implausible.

or

Parameterization error or internal error Parameter block 041 is implausible.

or

Parameterization error or internal error Parameter block 042 is implausible.

or

Parameterization error or internal error Parameter block 043 is implausible.

or

Parameterization error or internal error Parameter block 044 is implausible.

or

Parameterization error or internal error Parameter block 049 is implausible.

or

Parameterization error or internal error Parameter block 050 is implausible.

or

Parameterization error or internal error Parameter block 051 is implausible.

or

Parameterization error or internal error Parameter block 059 is implausible.

or

Parameterization error or internal error Parameter block 060 is implausible.

or

Parameterization error or internal error Parameter block 061 is implausible.

or

Parameterization error or internal error Parameter block 069 is implausible.

or

Parameterization error or internal error Parameter block 070 is implausible.

or

Parameterization error or internal error Parameter block 071 is implausible.

or

Parameterization error or internal error Parameter block 072 is implausible.

or

Parameterization error or internal error Parameter block 073 is implausible.

or

Parameterization error or internal error Parameter block 079 is implausible.

or

Parameterization error or internal error Parameter block 080 is implausible.

or

Parameterization error or internal error Parameter block 089 is implausible.

or

Parameterization error or internal error Parameter block 090 is implausible.

or

Parameterization error or internal error Parameter block 091 is implausible.

or

Parameterization error or internal error Parameter block 092 is implausible.

or

Parameterization error or internal error Parameter block 099 is implausible.

or

Parameterization error or internal error Parameter block 100 is implausible.

or

Parameterization error or internal error Parameter block 101 is implausible.

or

Parameterization error or internal error Parameter block 109 is implausible.

or

Parameterization error or internal error Parameter block 110 is implausible.

or

Parameterization error or internal error Parameter block 111 is implausible.

or

Parameterization error or internal error Parameter block 112 is implausible.

or

Parameterization error or internal error Parameter block 113 is implausible.

or

Parameterization error or internal error Parameter block 114 is implausible.

or

Parameterization error or internal error Parameter block 115 is implausible.

or

Parameterization error or internal error Parameter block 116 is implausible.

or

Parameterization error or internal error Parameter block 117 is implausible.

or

Parameterization error or internal error Parameter block 118 is implausible.

or

Parameterization error or internal error Parameter block 119 is implausible.

or

Parameterization error or internal error Parameter block 120 is implausible.

or

Parameterization error or internal error Parameter block 129 is implausible.

or

Parameterization error or internal error Parameter block 130 is implausible.

or

Parameterization error or internal error Parameter block 131 is implausible.

or

Parameterization error or internal error Parameter block 132 is implausible.

or

Parameterization error or internal error Parameter block 133 is implausible.

or

Parameterization error or internal error Parameter block 139 is implausible.

or

Parameterization error or internal error Parameter block 140 is implausible.

or

Parameterization error or internal error Parameter block 149 is implausible.

or

Parameterization error or internal error Parameter block 150 is implausible.

or

Parameterization error or internal error Parameter block 151 is implausible.

or

Parameterization error or internal error Parameter block 152 is implausible.

or

Parameterization error or internal error Parameter block 153 is implausible.

or

Parameterization error or internal error Parameter block 154 is implausible.

or

Parameterization error or internal error Parameter block 158 is implausible.

or

Parameterization error or internal error Parameter block 159 is implausible.

or

Parameterization error or internal error Parameter block 160 is implausible.

or

Parameterization error or internal error Parameter block 169 is implausible.

or

Parameterization error or internal error Parameter block 170 is implausible.

or

Parameterization error or internal error Parameter block 178 is implausible.

or

Parameterization error or internal error Parameter block 179 is implausible.

or

Parameterization error or internal error Parameter block 200 is implausible.

or

Parameterization error or internal error Parameter block 201 is implausible.

or

Parameterization error or internal error Parameter block 209 is implausible.

or

Parameterization error or internal error Parameter block 210 is implausible.

or

Parameterization error or internal error Parameter 'ap_p_Cal.IdlePos_u16' is incorrectly set.

or

Parameterization error or internal error Parameter 'ap_p_TrqConf.RpmMaxPos_u16 > 100%' is incorrectly set.

or

Parameterization error or internal error Parameter 'ap_p_TrqConf.RpmMinPos_u16 > 100%' is incorrectly set.

or

Parameterization error or internal error Parameter 'lgr_p_Cal.SubstSpeedRatio_u16 <119h; >753h außer 0' is incorrectly set.

or

Parameterization error or internal error Parameter 'ebm_p_EngConf.MapNr_u8 > 250' is incorrectly set.

or

Parameterization error or internal error Parameter 'lim_p_VehBdyOem.CustMaxVehSpeed_u16 > 150 km/h' is incorrectly set.

or

Parameterization error or internal error Parameter 'lim_p_LegConf.LegMaxVehSpeed_u16 > 150 km/h' is incorrectly set.

or

Parameterization error or internal error Parameter 'trans_p_Cal.ClutchTrv_u16 > 99,9 mm' is incorrectly set.

or

Parameterization error or internal error Parameter 'trans_p_ClutchConf.ThreshClutchOpen_u8 < 55% (50% +Hyster.) > 95%(100% - Hyster.) trans_p_ClutchConf.ThreshClutchClosed_u8 > 45% (50% - Hyster.) < 5% (0% + Hyster.)' is incorrectly set.

or

Parameterization error or internal error Parameter 'trans_p_Cal.MaxClutchWear_u8 =0; > 100%' is incorrectly set.

or

Parameterization error or internal error Parameter 'trans_p_Cal.MaxClutchHotDisp_u8 =0; > 100% oder >= trans_p_Cal.MaxClutchWear_u8' is incorrectly set.

or

Parameterization error or internal error Parameter 'Trans_p_Cal.ClutchMaxDiff_u8 =0; > 100%' is incorrectly set.

or

Parameterization error or internal error Parameter 'trans_p_Cal.ClutchMaxWear_u16 >= 110 mm oder < 2 mm' is incorrectly set.

or

Parameterization error or internal error Parameter 'kein EPS und: kein Automat und: Drehzahlgeber vorhanden und:Split vorhanden und: trans_p_Cal.SplitLowRatio_u8 <0Ch; >FAh ausser 0' is incorrectly set.

or

Parameterization error or internal error Parameter 'kein EPS und: kein Automat und: Drehzahlgeber vorhanden und: trans_p_Cal.SplitHighRatio_u8 < 0Ch; > FAh ausser 0' is incorrectly set.

or

Parameterization error or internal error Parameter 'trans_p_TransConf.MaxTrqConvRatio_u16 > FAh oder =0' is incorrectly set.

or

Parameterization error or internal error Parameter 'Trans_p_RetConf.MaxOutTrq_u8 > 50000 Nm' is incorrectly set.

or

Parameterization error or internal error Parameter 'Ebm_p_RetConf.MaxLeverPos_u8 <1 oder >5' is incorrectly set.

or

Parameterization error or internal error Parameter 'lim_p_VehBdyOem.IdleSpeed_u8 >= lim_p_VehBdyOem.MaxIdleSpeed_u8' is incorrectly set.

or

Parameterization error or internal error Parameter 'lim_p_VehBdyOem.IdleSpeed_u8 > Pto_p_VehBdyOem.IdleSpeedInc_u8; oder Pto_p_VehBdyOem.IdleSpeedInc_u8 > Pto_p_VehBdyOem.MaxSpeedLim_u8' is incorrectly set.

or

Parameterization error or internal error Parameter 'Ebm_p_RetConf.MaxLeverPos_u8 > 3 und Split vorhanden und Hebel an CPC' is incorrectly set.

or

Parameterization error or internal error Parameter 'Cc_p_Cal.ArtVcanAv_u1 und (trans_p_ClutchConf. ClutchInAv_u2 == switch oder brake_p_VehConf.ABSInDiflex01_u1 oder Ess_p_EngConf.EssEn_u1)' is incorrectly set.

or

Parameterization error or internal error Parameter 'ap_p_TrqConf.CharX1_u8 > ap_p_TrqConf.CharX2_u8 oder ap_p_TrqConf.CharY1_u8 > ap_p_TrqConf.CharY2_u8' is incorrectly set.

or

Parameterization error or internal error Parameter 'Cic_p_Gen.RateLimInc0Trq_u16 = 0 oder Cic_p_Gen.RateLimInc1Trq_u16 = 0 oder Cic_p_Gen.RateLimDecTrq_u8 = 0' is incorrectly set.

or

Parameterization error or internal error Parameter 'ap_p_TrqConf.RateLimInc_u8 = 0 oder ap_p_TrqConf.RateLimDec_u8 = 0' is incorrectly set.

or

Parameterization error or internal error Parameter 'trans_p_VehConf.DsdEn_u1 parametriert und: DST- Drehzahl-, oder Momenten-Stuetzstelle >FAH (Block 118)' is incorrectly set.

or

Parameterization error or internal error Parameter 'trans_p_VehConf.DsdEn_u1 parametriert und: DST- Drehzahl -Stuetzstelle ist fallend (Block 118)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 131: Hebelsimulation ueber BRE-Eingang (Unimog): ebm_p_VehConf.SimLeverPos_u8 == 0 oder ebm_p_VehConf.SimLeverPos_u8 > ebm_p_RetConf.MaxLeverPos_u8' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 070: Retarder -Luefterdatendatz: fan_p_RetConf.FanReq_u8 >250. Anmerkung: Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. fan_p_RetConf. RetMapNr_u8)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 072: Heckkuehl-Luefterdatendatz: fan_p_HdutyConf. SubstTransTemp_u8>250. Anmerkung Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. fan_p_HdutyConf. HdcMapNr_u8)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 071: Getriebe -Luefterdatendatz: fan_p_TransConf. SubstTransTemp_u8>250 Anmerkung: Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. fan_p_TransConf. TransMapNr_u8)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 071: Getriebe- Luefterdatendatz: fan_p_TransConf. SelSource_u1>1 Anmerkung: Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. fan_p_TransConf. TransMapNr_u8)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 133: Motorbrems -Datensatz: ebm_p_EbmConf.ErConfRetLeverSim_u1>1 Anmerkung: Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. ebm_p_EngConf.MapNr_u8)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 240: parametrierte HW-Variante (vdo_p_Gen.HwVar_u4) ungleich: 0=max,1=light, 3=mps,4=eps,5=nafta,6=row oder nicht kompatibel zu Hardwarebestueckung' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 030, 039: ART vorhanden und kein integrierter Tempomat und altes Tempomat-Bedienkonzept (Cc_p_Cal.ArtVcanAv_u1, cc_p_VehConf.CombCcEn_u1, cc_p_Cal.NewCcEn_u1)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 030, 039: ART vorhanden und kein Beschleunigungsregler und altes Tempomat-Bedienkonzept (Cc_p_Cal.ArtVcanAv_u1, cc_p_VehConf.OldCcGov_u1, cc_p_Cal.NewCcEn_u1)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 131: Hebelsimulation ueber BRE-Eingang (Unimog): kein CAN-faehiges ABS vorhanden' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 131: Retarderlampeninfo und LGS-Info auf Split-Ausgang High parametriert' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 131: ebm_p_VehConf.LeverPosThresh_u8 >= ebm_p_RetConf.MaxLeverPos_u8 parametriert' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 051: ADR-Reglertyp pto_p_VehBdyOem.ReqGov_u4 > 14 (d.h. s.n.v.)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 130 oder Block 111: Mehrfachparametrierung auf Ausgang MBA2: ebm_p_EngConf. EngBrkOutSel_u2 und trans_p_ClutchConf. ClutchOpenOutSel_u1' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 130 oder Block 000: Mehrfachparametrierung auf Ausgang MBA2: ebm_p_EngConf. EngBrkOutSel_u2 und cic_p_Gen.OnThreshAuto_u8' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 111 oder Block 000: Mehrfachparametrierung auf Ausgang MBA2: trans_p_ClutchConf. ClutchOpenOutSel_u1 und cic_p_Gen.OnThreshAuto_u8' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 000: cic_p_Gen.OnThreshAuto_u8, cic_p_Gen.OffThreshAuto_u8 unplausibel' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 000: cic_p_Gen.TrqDecZero_u16=0 oder cic_p_Gen.TrqDecNonZero_u16=0' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 013: SCR-Tankkennlinie: cdi_p_ScrConf.Nr_u16 > 49 !' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 014: Regelparameter: einzelne ungueltige float Zahl (z.B. FFFF.FFFF hex)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block29: Regelparameter vebm: ungueltige float Zahl!!!' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 131: ebm_p_VehConf. RetLeverSource_u2 im ungueltigen Bereich: 3..254!!!' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 112 (Split vorhanden) UND Block 117 (Single-H vorhanden)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 117 (Single-H-Feedback der uebersetzung ueber GSE, trans_p_SingleH.RangeInSel_u1) UND Block 42 (Begrenzung ueber GSE aktiv, lim_p_VehConf.LimSel_u1) ODER PID 42 (Klima ueber GSE, lim_p_VehConf.AcInSel_u1) ODER PID 112 (GSe parametriert, trans_p_Tran' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 131 (Verwendung von MBE0, ebm_p_VehConf.MBE0AsQuit_u1) UND max. Retarderhebelstellung > 2 (ebm_g_RetConfMaxLeverPos_u8)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 112 trans_p_TransConf.VehStopDly_u16 > 6s ODER < 20ms' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 43 lim_p_LegConf.RearAxleTransRatio_u16 > 2 ODER <1' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 180 UND Block 129, OESE mehrfach benutzt (ABS ueber OESE und HL5)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 180 UND Block Block 61, OESE mehrfach benutzt (HL5 und oelnachfuellung)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 180 UND Block 112 ODER Block 117, SSH mehrfach benutzt (HL5 UND Split oder Single-H)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 180 UND Motorbremseingang' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 180 trans_p_HL5.Sfp02ClosedDelay_u16 > 1000 (10s)' is incorrectly set.

or

Parameterization error or internal error Parameter 'Block 61, MOEL-Ausgang mehrfach benutzt (Geschwindigkeitsstatus (Brasilien) UND Oelnachfuellung)' is incorrectly set.

or

Parameterization error or internal error Parameter 'SPI-EEPROM von Software angefordert, aber nicht vorhanden' is incorrectly set.

or

Parameterization error or internal error

7061

Fault in parameter 'Configuration of engine brake' Parameter block 000 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 009 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 010 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 011 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 012 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 013 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 014 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 015 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 019 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 020 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 021 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 022 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 023 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 024 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 029 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 030 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 031 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 032 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 039 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 040 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 041 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 042 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 043 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 044 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 049 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 050 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 051 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 059 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 060 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 061 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 069 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 070 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 071 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 072 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 073 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 079 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 080 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 089 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 090 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 091 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 092 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 099 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 100 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 101 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 109 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 110 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 111 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 112 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 113 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 114 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 115 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 116 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 117 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 118 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 119 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 120 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 129 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 130 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 131 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 132 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 133 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 139 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 140 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 149 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 150 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 151 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 152 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 153 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 154 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 158 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 159 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 160 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 169 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 170 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 178 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 179 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 200 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 201 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 209 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter block 210 is implausible.

or

Fault in parameter 'Configuration of engine brake' Parameter 'ap_p_Cal.IdlePos_u16 £ 1%' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'ap_p_TrqConf.RpmMaxPos_u16 > 100%' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'ap_p_TrqConf.RpmMinPos_u16 > 100%' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'lgr_p_Cal.SubstSpeedRatio_u16 <119h; >753h außer 0' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'ebm_p_EngConf.MapNr_u8 > 250' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'lim_p_VehBdyOem.CustMaxVehSpeed_u16 > 150 km/h' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'lim_p_LegConf.LegMaxVehSpeed_u16 > 150 km/h' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'trans_p_Cal.ClutchTrv_u16 > 99,9 mm' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'trans_p_ClutchConf.ThreshClutchOpen_u8 < 55% (50% +Hyster.) > 95%(100% - Hyster.) trans_p_ClutchConf.ThreshClutchClosed_u8 > 45% (50% - Hyster.) < 5% (0% + Hyster.)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'trans_p_Cal.MaxClutchWear_u8 =0; > 100%' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'trans_p_Cal.MaxClutchHotDisp_u8 =0; > 100% oder >= trans_p_Cal.MaxClutchWear_u8' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Trans_p_Cal.ClutchMaxDiff_u8 =0; > 100%' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'trans_p_Cal.ClutchMaxWear_u16 >= 110 mm oder < 2 mm' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'kein EPS und: kein Automat und: Drehzahlgeber vorhanden und:Split vorhanden und: trans_p_Cal.SplitLowRatio_u8 <0Ch; >FAh ausser 0' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'kein EPS und: kein Automat und: Drehzahlgeber vorhanden und: trans_p_Cal.SplitHighRatio_u8 < 0Ch; > FAh ausser 0' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'trans_p_TransConf.MaxTrqConvRatio_u16 > FAh oder =0' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Trans_p_RetConf.MaxOutTrq_u8 > 50000 Nm' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Ebm_p_RetConf.MaxLeverPos_u8 <1 oder >5' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'lim_p_VehBdyOem.IdleSpeed_u8 >= lim_p_VehBdyOem.MaxIdleSpeed_u8' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'lim_p_VehBdyOem.IdleSpeed_u8 > Pto_p_VehBdyOem.IdleSpeedInc_u8; oder Pto_p_VehBdyOem.IdleSpeedInc_u8 > Pto_p_VehBdyOem.MaxSpeedLim_u8' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Ebm_p_RetConf.MaxLeverPos_u8 > 3 und Split vorhanden und Hebel an CPC' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Cc_p_Cal.ArtVcanAv_u1 und (trans_p_ClutchConf. ClutchInAv_u2 == switch oder brake_p_VehConf.ABSInDiflex01_u1 oder Ess_p_EngConf.EssEn_u1)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'ap_p_TrqConf.CharX1_u8 > ap_p_TrqConf.CharX2_u8 oder ap_p_TrqConf.CharY1_u8 > ap_p_TrqConf.CharY2_u8' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Cic_p_Gen.RateLimInc0Trq_u16 = 0 oder Cic_p_Gen.RateLimInc1Trq_u16 = 0 oder Cic_p_Gen.RateLimDecTrq_u8 = 0' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'ap_p_TrqConf.RateLimInc_u8 = 0 oder ap_p_TrqConf.RateLimDec_u8 = 0' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'trans_p_VehConf.DsdEn_u1 parametriert und: DST- Drehzahl-, oder Momenten-Stuetzstelle >FAH (Block 118)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'trans_p_VehConf.DsdEn_u1 parametriert und: DST- Drehzahl -Stuetzstelle ist fallend (Block 118)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 131: Hebelsimulation ueber BRE-Eingang (Unimog): ebm_p_VehConf.SimLeverPos_u8 == 0 oder ebm_p_VehConf.SimLeverPos_u8 > ebm_p_RetConf.MaxLeverPos_u8' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 070: Retarder -Luefterdatendatz: fan_p_RetConf.FanReq_u8 >250. Anmerkung: Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. fan_p_RetConf. RetMapNr_u8)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 072: Heckkuehl-Luefterdatendatz: fan_p_HdutyConf. SubstTransTemp_u8>250. Anmerkung Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. fan_p_HdutyConf. HdcMapNr_u8)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 071: Getriebe -Luefterdatendatz: fan_p_TransConf. SubstTransTemp_u8>250 Anmerkung: Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. fan_p_TransConf. TransMapNr_u8)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 071: Getriebe- Luefterdatendatz: fan_p_TransConf. SelSource_u1>1 Anmerkung: Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. fan_p_TransConf. TransMapNr_u8)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 133: Motorbrems -Datensatz: ebm_p_EbmConf.ErConfRetLeverSim_u1>1 Anmerkung: Die Pruefung erfolgt nur wenn der Datensatz verwendet wird (siehe Param. ebm_p_EngConf.MapNr_u8)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 240: parametrierte HW-Variante (vdo_p_Gen.HwVar_u4) ungleich: 0=max,1=light, 3=mps,4=eps,5=nafta,6=row oder nicht kompatibel zu Hardwarebestueckung' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 030, 039: ART vorhanden und kein integrierter Tempomat und altes Tempomat-Bedienkonzept (Cc_p_Cal.ArtVcanAv_u1, cc_p_VehConf.CombCcEn_u1, cc_p_Cal.NewCcEn_u1)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 030, 039: ART vorhanden und kein Beschleunigungsregler und altes Tempomat-Bedienkonzept (Cc_p_Cal.ArtVcanAv_u1, cc_p_VehConf.OldCcGov_u1, cc_p_Cal.NewCcEn_u1)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 131: Hebelsimulation ueber BRE-Eingang (Unimog): kein CAN-faehiges ABS vorhanden' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 131: Retarderlampeninfo und LGS-Info auf Split-Ausgang High parametriert' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 131: ebm_p_VehConf.LeverPosThresh_u8 >= ebm_p_RetConf.MaxLeverPos_u8 parametriert' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 051: ADR-Reglertyp pto_p_VehBdyOem.ReqGov_u4 > 14 (d.h. s.n.v.)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 130 oder Block 111: Mehrfachparametrierung auf Ausgang MBA2: ebm_p_EngConf. EngBrkOutSel_u2 und trans_p_ClutchConf. ClutchOpenOutSel_u1' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 130 oder Block 000: Mehrfachparametrierung auf Ausgang MBA2: ebm_p_EngConf. EngBrkOutSel_u2 und cic_p_Gen.OnThreshAuto_u8' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 111 oder Block 000: Mehrfachparametrierung auf Ausgang MBA2: trans_p_ClutchConf. ClutchOpenOutSel_u1 und cic_p_Gen.OnThreshAuto_u8' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 000: cic_p_Gen.OnThreshAuto_u8, cic_p_Gen.OffThreshAuto_u8 unplausibel' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 000: cic_p_Gen.TrqDecZero_u16=0 oder cic_p_Gen.TrqDecNonZero_u16=0' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 013: SCR-Tankkennlinie: cdi_p_ScrConf.Nr_u16 > 49 !' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 014: Regelparameter: einzelne ungueltige float Zahl (z.B. FFFF.FFFF hex)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block29: Regelparameter vebm: ungueltige float Zahl!!!' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 131: ebm_p_VehConf. RetLeverSource_u2 im ungueltigen Bereich: 3..254!!!' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 112 (Split vorhanden) UND Block 117 (Single-H vorhanden)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 117 (Single-H-Feedback der uebersetzung ueber GSE, trans_p_SingleH.RangeInSel_u1) UND Block 42 (Begrenzung ueber GSE aktiv, lim_p_VehConf.LimSel_u1) ODER PID 42 (Klima ueber GSE, lim_p_VehConf.AcInSel_u1) ODER PID 112 (GSe parametriert, trans_p_Tran' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 131 (Verwendung von MBE0, ebm_p_VehConf.MBE0AsQuit_u1) UND max. Retarderhebelstellung > 2 (ebm_g_RetConfMaxLeverPos_u8)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 112 trans_p_TransConf.VehStopDly_u16 > 6s ODER < 20ms' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 43 lim_p_LegConf.RearAxleTransRatio_u16 > 2 ODER <1' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 180 UND Block 129, OESE mehrfach benutzt (ABS ueber OESE und HL5)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 180 UND Block Block 61, OESE mehrfach benutzt (HL5 und oelnachfuellung)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 180 UND Block 112 ODER Block 117, SSH mehrfach benutzt (HL5 UND Split oder Single-H)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 180 UND Motorbremseingang' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 180 trans_p_HL5.Sfp02ClosedDelay_u16 > 1000 (10s)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'Block 61, MOEL-Ausgang mehrfach benutzt (Geschwindigkeitsstatus (Brasilien) UND Oelnachfuellung)' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake' Parameter 'SPI-EEPROM von Software angefordert, aber nicht vorhanden' is incorrectly set.

or

Fault in parameter 'Configuration of engine brake'

7064

Control module has an internal error.

7070

Accelerator pedal unit not learned

7071

Learning error with splitter ratio

7072

Learning error with terminal W ratio

7073

Learning error with clutch travel sensor

7074

Learning error at vehicle CAN bus

8023

Position of switch HL5 implausible