sm5461d000503ts

Convert rpm sensor for digital tachograph (DTCO), 2nd generation

Typ sm · téma 54.61 · verze 0100 · 2019-05-15

Platí pro: Model 907 with code JD2 (Tachograph digital EC with rpm + aux-recorder) Model 907 with code JV6 (Tachograph pre-installation kit)

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 2 Podvozek › 54 Elektrické zařízení, výstroj a přístroje › 54.61 Tachograf, zapisovač jízd, taxametr — Řada 907

EinPAS 31 Komunikace/informace/zábava › 31.35 Tachograf/systém výběru mýtného › 31.35.3 Dodatečná montáž/přemontování — Řada 907

EinPAS 45 Data/informace › 45.20 Informace/opatření › 45.20.40 Servisní opatření — Řada 907

SM54.61-D-0005-03TS

Convert rpm sensor for digital tachograph (DTCO), 2nd generation

Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

Model

907

with code JD2 (Tachograph digital EC with rpm + aux-recorder)

Model

907

with code JV6 (Tachograph pre-installation kit)

Repair materials

Number

Designation

Order number

BR00.45-Z-1001-06A

Long-life grease

A 000 989 63 51 11

Convert rpm sensor for digital tachograph (DTCO), 2nd generation

D54.61-A013-08

Shown on model 907 with manual transmission

1

Remove lead seal (1).

The lead seal (1) is irreparably damaged during removal.

2

Remove rpm sensor (2).

To do so, remove screw of rpm sensor (2).

3

Remove electric line (3) from factory-installed subharness.

To do so, cut through the cable ties.

4

Open feed-through grommet (4).

To do so, separate cable tie.

Convert rpm sensor for digital tachograph (DTCO), 2nd generation

5

Carefully guide electric line (3) out of feed-through grommet (4) until connector coupling (5) is accessible.



6

Disconnect connector coupling (5).


D54.61-A014-11

Convert rpm sensor for digital tachograph (DTCO), 2nd generation

7

Lightly grease sealing ring of new rpm sensor (6).



8

Install new rpm sensor (6).



9

Screw in screw/bolt (7).


Shown on model 907 with manual transmission and code N05 (Power take-off countershaft (2c) without flange)

D54.61-A015-01

Convert rpm sensor for digital tachograph (DTCO), 2nd generation

D54.61-A024-09

10

Route and attach electric line (8) as shown.

Do not kink electric line (8) and ensure that it is routed without chafing.
Prevent damage.

To do so, secure electric line (8) with cable ties.

Model 907 with code GD8 (6-speed manual transmission, ECO Gear 360) except code N05 (Power take-off countershaft (2c) without flange), Model 907 with code GD9 (6-speed manual transmission, ECO Gear 480)
See Fig. A.

Model 907 with code GD8 (6-speed manual transmission, ECO Gear 360) with code N05 (Power take-off countershaft (2c) without flange)
See Fig. B.

Model 907 with code ZG1 (All-wheel drive, engageable) or code ZG3 (Engageable all-wheel drive with transmission ratio)
See fig. C.

Model 907 with code G43 (9G-TRONIC) or code G42 (7G-TRONIC PLUS) except code ZG1 (All-wheel drive, engageable) and except code ZG3 (Engageable all-wheel drive with transmission ratio)
See fig. D.

Model 907 with code G42 (7G-TRONIC PLUS) with code ZG1 (All-wheel drive, engageable), Model 907 with code G42 (7G-TRONIC PLUS) with code ZG3 (Engageable all-wheel drive with transmission ratio)
See fig. E.

11

Connect electrical connector (5) and guide into feed-through grommet (4).

12

Seal feed-through grommet (4).

To do so, use a cable tie.

Odkazované dokumenty