Parts ordering notes
Part no. | Designation | Quantity |
A 670 553 02 16 | Kit 3 - Retrofitting B65 12 V | |
A 670 553 03 16 | Kit 4 - Retrofitting B65 24 V | |
Parts identified with X1 below are included in parts kit 3 Parts identified with X2 below are included in parts kit 4 | ||
A 001 431 98 15 | X1 Heated compressed-air drier (12 V) or | 1 |
A 001 431 97 15 | X2 Heated compressed-air drier (24 V) | 1 |
A 668 420 02 71 | X1/2 Safety valve assy. or | 1 |
A 668 420 03 71 | Safety valve assy. (only with 4800 wheelbase and transmission G60 or automatic) and | 1 |
A 668 427 19 41 | bracket (only with 4800 wheelbase and transmission G60 or automatic) | 1 |
A 020 545 71 32 | X1 Time-delay relay (12 V) or | 1 |
A 020 545 72 32 | X2 Time-delay relay (24 V) | 1 |
N 007 981 004 325 | X1/2 Sheet-metal screw for time-delay relay bracket | 1 |
A 670 540 74 36 | X1/2 Waist rail wiring harness (for time-delay relay) | 1 |
A 669 540 54 36 | X1/2 Frame wiring harness (for all wheelbases) | 1 |
N 304 017 008 030 | X1/2 ISO M8x50 hexagon bolts | 2 |
A 668 427 20 41 | X1/2 Bracket for safety valve | 1 |
N 000 000 000 932 | X1/2 Clamp for safety valve | 1 |
N 914 146 006 102 | X1/2 M6x16 hexagon bolt | 1 |
N 913 023 006 001 | X1/2 M6x8 nut | 1 |
N 000 908 022 011 | X1/2 M22x1.5 plug | 1 |
N 007 603 022 403 | X1/2 Sealing ring (for opening of old safety valve) | 1 |
N 007 603 012 405 | X1/2 Sealing rings | 4 |
A 668 545 47 45 | X1/2 Pipe line (7.5m between drier + distributor) If necessary, shop-made from: 1 x plug A 000 990 68 78, 1 x right-angle plug A 002 990 28 71, 1 x elbow A 655 990 06 71, plastic pipe 12x1.5 m length 7.5 m A 000 987 28 27 | 1 |
A 000 997 08 34 | X1/2 Union screw (small) | 1 |
A 000 997 09 34 | X1/2 Union screw (large) | 1 |
A 000 994 00 47 | X1/2 Locking ring (small) | 1 |
A 000 994 01 47 | X1/2 Locking ring (large) | 1 |
A 000 994 12 48 | X1/2 Retaining clip (small) | 1 |
A 000 994 14 48 | X1/2 Retaining clip (large) | 1 |
A 005 997 89 72 | X1/2 Tube | 1 |
A 006 997 30 90 | X1/2 Cable strap | 10 |
A 001 997 84 90 | X1/2 Cable strap | 20 |
1 Clip contact pin into chamber 5 and chamber 7
Clip contact pin on red/yellow cable on the black connector XF.B5 into chamber 5 (co-driver's footwell) and contact pin on the black/yellow cable into chamber 7.
Frame wiring harness (A 669 540 54 36)
N42.20-2036-05
2 Screw ground cable onto frame
Screw brown ground cable to ground on left of frame at the level of the rear edge of the cab.
3 Route wiring harness
The wiring harness runs through the right of the firewall into the engine compartment, to the left of the coupling jaw cross member and from there back over the frame cross member to the right to the compressed-air drier.
1 Waist rail wiring harness
2 Compressor
3 Compressed-air line
4 Frame wiring harness
N42.20-2019-01
4 Screw on plug R 37 and R38
Screw plug R 37 of wiring harness onto drainage valve of compressed-air drier and screw plug R 38 onto compressed-air drier heater. Loop cable on frame if necessary.