SI54.21-B-0041A | Service Information: Update software of telematics platform module (TP5) and reset to manufacturer default setting | 12.02.16 |
Vehicle 693, 694, 695, 696, 958, 979
This service information has the objective of guiding on the procedures necessary for the configuration of the TP5 module of the Telematic Platform for factory values and parameterization of the TP5 module in the retrofitting of the FleetBoard.
Remark: For the SG process, the concessionaire must attach a copy of the SdA form filled out and signed by the customer and SdFR filled out by the concessionaire and signed by the customer and concessionaire.
Codification for anomaly 82370 ED / TPR 02 9288.
B54.18-0046-01
Introduction
Flash for software updating of the TP5 module co-processor.
The following is necessary to carry out the procedure:
- Xentry kit with at least 12/2014 update.
- All AddOns installed, mainly the AddOns 1254 and 4290.
- Adapter cable HSD 000 000 00 04.
B54.18-0047-02
1.0 - Flash for updating of the TP5 module co-processor
1.1 - Connect the Xentry kit to the diagnosis outlet (X13).
1.2 - Initiate and carry out the vehicle identification through the Xentry.
B54.18-0048-05
1.3 - In the DAS carry out quick test.
B54.18-0049-05
1.4 - Access module TP and click on F3.
B54.18-0050-05
1.5 - Access the option "Programming of the control modules (SDflash) and click on F3.
B54.18-0051-05
1.6 - Provide the adaptation cable (number HSD 000 000 00 04) and click on F2.
B54.18-0052-05
1.7 - Select programming through the Hard Disc and click on F3.
B54.18-0053-05
1.8 - Proceed clicking on F3.
B54.18-0054-05
1.9 - Install the adaptation cable as stated below and then click on F2.
B54.18-0055-04
1 - Connector.
2 - Connector.
3 - Connector for OBD outlet.
4 - Adaptation cable HSD 000 000 00 04 for programming of the control module.
A3: Control module for vehicle control (FR CPC).
A3X2: Control module connector of vehicle control (FR CPC).
B54.18-0056-05
1.10 - Wait for the end of the programming to proceed.
B54.18-0057-05
1.11 - Separate the diagnosis apparatus from the adaptation cable according to procedure below and proceed clicking on F2.
B54.18-0058-05
1.12 - Duly fill out the job order documentation and carry out the printing through the key F11.
B54.18-0059-05
1.13 - Wait for message of conclusion below and click on F2.
Reset procedure for "Factory Values" | |||
| This procedure must be carried out before the steps below . | Form for "Request of Factory Reset and Updating of Firmware, and the configuration of the Telematic Platform module to the factory values and parameterization of the vehicle modules in the retrofitting of the FleetBoard | |
| 2 - Star Diagnosis | ||
2.1 | Access | ||
2.2 | Identify the vehicle through the VIN | ||
2.3 | Select "Continue" | ||
2.4 | Select "Xentry Diagnostics"" | ||
2.5 | In the DAS, carry out quick test | ||
2.6 | Access the control module “TP Telematik Platform" | ||
| 3 - TP Telematik Platform (TP) | ||
3.1 | Select "Adaptations of the control module" | ||
3.2 | Select “Special functions" | ||
3.3 | Select “Factory settings” | ||
3.4 | Insert the password informed by the DAC as requested | ||
3.5 | The parameterization is reestablished for its original condition. Confirming keying F3 | ||
| 4 - Return to the DAS main screen and update the data with the key "F5" | ||
4.1 | Eliminate the fault codes of the electronic units |