ar8610p0102mbc

Remove/install fire extinguishing system temperature sensor

Typ ar · téma 86.10 · verze 0100 · 2004-11-29

Platí pro: MODEL 220.1 /8 as of 15.4.04 with CODE (Z04) Light armoring with CODE (Z07) Top protection with fire extinguishing system, engine fire extinguishing system temperature sensor

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 3 Nástavba › 86 Nouzová zařízení, výbava pro postižené osoby, sanitární vybavení, kuchyňka › 86.10 Nouzové přístroje — Řada 220 (modely 1**, 8**)

EinPAS 27 Systémy pasivní bezpečnosti/zádržné systémy › 27.21 Hasicí zařízení/systém hlášení požáru › 27.21.12 Snímač/spínač/kabelový svazek — Řada 220 (modely 1**, 8**)

AR86.10-P-0102MBC

Remove/install fire extinguishing system temperature sensor

25.10.04

MODEL 220.1 /8 as of 15.4.04
with CODE (Z04) Light armoring
with CODE (Z07) Top protection
with fire extinguishing system,
engine fire extinguishing system temperature sensor

Remove/install fire extinguishing system temperature sensor

P86.10-2168-09

Shown on model 220.1

1 Electrical line

2 Electrical line

3 Bolts

4 Bolts

B65x1 Engine fire extinguishing system temperature sensor connector

B65 Engine fire extinguishing system temperature sensor

Remove/Install

Danger of actuating fire extinguishing system when the work sequence is not observed.

1

Ignition Off, detach transmitter key from the electronic ignition switch control unit

2

Remove fuses no. 54 and no. 58 from rear fuse and relay module

The rear fuse and relay module is located below the right rear seat

See

Fuse assignment of rear fuse and relay box

GF54.15-P-1256-01MB

3

Open engine hood

See Operator's Manual

4.1

Disconnect fire extinguishing system temperature sensor connector (B65x1) and expose electrical line (1)

When removing fire extinguishing system temperature sensor (B65) at top on left spring strut tower.

Installation: Ensure that the fire extinguishing system temperature sensor connector (B65x1) is free of moisture and dirt.Danger of erroneous actuation.

5.1

Unscrew bolts (3) and remove fire extinguishing system temperature sensor (B65) at top on spring strut tower

When removing fire extinguishing system temperature sensor (B65) at top on left spring strut tower .

6.1

Disconnect fire extinguishing system temperature sensor connector (B65x1) and expose electrical line (2)

When removing fire extinguishing system temperature sensor (B65) at bottom left on front wheel carrier.

Installation: Ensure that the fire extinguishing system temperature sensor connector (B65x1) is free of moisture and dirt.Danger of erroneous actuation.

Danger!

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

7.1

Raise vehicle.

When removing fire extinguishing system temperature sensor (B65) at bottom left on front wheel carrier.

Do not damage extinguishing agent lines on fire extinguishing system when jacking up vehicle.

8.1

Unscrew bolts (4) and fire extinguishing system temperature sensor (B65) at bottom left on front wheel carrier

When removing fire extinguishing system temperature sensor (B65) at bottom left on front wheel carrier.

9

Install in the reverse order

10

Perform self-test for fire extinguishing system

AR86.10-P-0101-01MB

Odkazované dokumenty