ar8370p117701a

Checking emission level with gas trace instrument

Typ ar · téma 83.70 · verze 0116 · 2006-07-26

Platí pro: MODEL 210.### ## up to 636643 with ENGINE 604, 605, 606 with CODE (228) Stationary heater Heizgerät Thermo Top S MODEL 210.### ## up to 672083 with ENGINE 104, 111, 112, 113, 119 with CODE (228) Stationary heater MODEL 461 with ENGINE 602.983 with CODE (H12) Auxiliary heater MODEL 463 as of 1.9.96 up to 30.11.00 with CODE (H12) Auxiliary heater MODEL 202 up to 31.5.97 mit nachträglich eingebauter Standheizung Thermo Top S MODEL 210.### ## up to 340566 with ENGINE 602.982 mit Zuheizer oder nachträ

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 3 Nástavba › 83 Klimatizace › 83.70 Nezávislé topení, přídavné topení, přihřívač — Řada 202 · Řada 210 · Řada 461 · Řada 463 · Řada 602 (modely 982, 983)

EinPAS 39 Topení/větrání/chlazení › 39.25 Nezávislé topení/přídavné topení › 39.25.47 Výfuková soustava — Řada 202 · Řada 210 · Řada 461 · Řada 463 · Řada 602 (modely 982, 983)

Platí také pro motory/převodovky: 104 ***, 111 ***, 112 ***, 113 ***, 119 ***, 604 ***, 605 ***, 606 ***

AR83.70-P-1177-01A

Checking emission level with gas trace instrument

Danger!

Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit

Do not operate stationary heater, auxiliary heater or engine with heater booster in closed areas or when refueling. Allow heater unit to cool down after operation or wear protective gloves.

AS83.70-Z-0002-01A

Thermo Top S heater unit test values

Number

Designation

Model 202

Model 210

Model 461

Model 463

BE83.70-P-1001-03A

CO2 value in exhaust gas (diesel)

Wide open throttle operation

vol %

9,5-12,0

9,5-12,0

9,5-12,0

9,5-12,0

BE83.70-P-1002-03A

CO2 value in exhaust gas (gasoline)

Wide open throttle operation

vol %

9,5-12,0

9,5-12,0

9,5-12,0

9,5-12,0

Commercially available tools

Number

Designation

WH58.30-Z-1010-13A

CO2 test tubes, 1 to 20 percent by volume

WH58.30-Z-1012-13A

Gas detector

WH58.30-Z-1013-13A

Vehicle emissions sensor

WH58.30-Z-1019-13A

Hot air sensor

Checking emission level with gas trace instrument

P83.70-0236-01

1 Operate stationary heater or heater booster.

2 Break off both ends of the CO2 test tube.

Checking emission level with gas trace instrument

P83.70-0237-01

3 Insert end of the CO2 test tube with the high scale value in the gas trace instrument .

4 Mount the hot air sensor or motor vehicle emission gas sensor on the other end of the CO2 test tube.

5.1 Seal the second outlet (arrow) gas-tight.

Only when the vehicle emission sensor is used.

Checking emission level with gas trace instrument

P83.70-0238-01

6 Let heater of stationary heater or heater booster run under full load.

7 Compress the rubber bellows of the gas trace instrument by hand and keep pressed.

8 Insert the hot air sensor or motor vehicle emission sensor in the exhaust gas outlet.

Checking emission level with gas trace instrument

P83.70-0239-01

9 Release the rubber bellows and wait until the chain (arrow) is tensioned.

10 Withdraw the gas trace instrument from the exhaust gas outlet, read off emission level and compare with the specified values.

11 Adjust CO2 level in exhaust if necessary.

12 Switch off stationary heater or heater booster.

Odkazované dokumenty