AR42.10-B-0500F | Remove/install brake carrier | 12.02.16 |
Vehicle 688 with Cumbustion engine 374.905, 374.951, 374.994, 374.990, 374.950, 304.900, 308.900, 374.984, 374.980, 374.996, 374.993, 374.991, 374.988, 374.986, 374.953, 906.924, 374.907, 374.989, 374.952
B42.10-0467-06
1 Case
2 Brake shoe support
3 Guide bearing
4 Brake pads
5 Brake pad damping spring
6 Screw
7 Protection bellows of the guide bushings
8 Threaded plug
9 Cylindrical bolt
10 Cylindrical bolt
11 Guide bushing
B42.10-0349-06
1 Case
2 Brake shoe support
3 Guide bearing
7 Protection bellows of the guide bushings
8 Threaded plug
9 Cylindrical bolt
10 Cylindrical bolt
11 Guide bushing
| REMOVAL | ||
| Indications referring to brake system repairs | ||
1 | Park the vehicle on flat and level ground. | ||
Danger | Risk of life by the vehicle slipping or falling from the lifter | Position the vehicle on a suitable elevator so the wheels of the front axle, rear drive axle and rear auxiliary axle remain supported safely on the four or six elevator support plates, at the elevating points determined by the vehicle manufacturer. | |
2 | Support the vehicle on safety stands, arranged under the chassis on both sides, that permit disassembling the wheels and carrying out brake jobs safely. | ||
3 | Remove the brake pads. | ||
4 | Install the support with the brake caliper | ||
5 | Loosen the cylindrical bolts (9) and remove the bearing (3) | ||
6 | Remove from the case (1) the support (2) | Displace the protection bellows (7) from the guide-bushings (11), utilizing a suitable pin. | |
7 | Unscrew and remove the threaded plugs (8) | ||
8 | Unscrew and remove the cylindrical bolts (10) from the guide bushings (11) | ||
9 | Remove the guide bushings (11) | If necessary, utilize a rubber head hammer to detach the guide-bushings (11) from the support (2). | |
| CLEAN | ||
10 | Clean the housing of the guide bushings (11) on the support (2) | ||
| Check | ||
11 | Check the guide bushings (11) and their housing in the support (2) | When presenting wear or oxidation, replace them | |
| Installing | ||
12 | Install new support (2) inserting the guide bushings (11) | Lightly tighten the cylindrical bolts (10). | |
Lubricate the housing of the bushings on the support (2), the guide-bushings (11) and the inside of the protection bellows (7). | |||
13 | Insert the support (2) in the case (1) | Observe the correct positioning of the new protection bellows (7) in the guide-bushings (11). | |
14 | Tighten the cylindrical bolts (10) | Apply the specified tightening torque to the cylindrical bolts. Observe making sure the parts move easily. | |
| |||
15 | Install new threaded plugs (8) | Tighten the plugs (8) to specified torque. | |
| |||
16 | Install the bearing (3) | Tighten the bolts (9) to specified torque. | |
| |||
17 | Install the support with the brake caliper | ||
18 | Install the brake pads. | ||
19 | Bleed the brake system | ||
20 | Check the tightness and operation of the service brake system |
Front axle brake caliper
Número | Denominação | Front axle 732.510/561; 733.840/882 | |||
BA42.10-B-1004-10A | Brake caliper guiding bearing bolts | Hydro-vacuum brake | M12x1.5 | Nm | 100...115 |
Hydro-vacuum brake | M16x1.5 | Nm | - | ||
Pneumatic brake | M16x1.5 - first stage | Nm | - | ||
M16x1.5 - second stage | degrees | - | |||
BA42.10-B-1007-10A | Threaded plug | Nm | 30...35 | ||
Produtos para reparos
Número | Denominação | Número de pedido |
BR00.45-B-1007-06A | Grease DBL 6812.00 | Klueber Lubrification |