ar4020g020014k

Adjust driveline angle

Typ ar · téma 40.20 · verze 0105 · 2013-11-19

Platí pro: MODEL 000.069 with REAR AXLE 749.301/306/307/320/321/322/330/335/337/340/347/348 with air suspensionHT250 MODEL 000.069 with REAR AXLE 749.323/336/345/346 with HDB air suspension

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 2 Podvozek › 40 Kola, měření geometrie podvozku › 40.20 Měření geometrie podvozku — Řada 000 (modely 069)

EinPAS 20 Podvozek › 20.10 Měření podvozku › 20.10.20 Diagnostika/zkouška/proměření/nastavení — Řada 000 (modely 069)

Platí také pro motory/převodovky: 749 301, 749 306, 749 307, 749 320, 749 321, 749 322, 749 323, 749 330, 749 335, 749 336, 749 337, 749 340, 749 345, 749 346, 749 347, 749 348

AR40.20-G-0200-14K

Adjust driveline angle

Remove/install axle housing

AR35.10-G-0031K

MODEL

000.069 with REAR AXLE 749.301/306/307/320/321/322/330/335/337/340/347/348

with air suspensionHT250

MODEL

000.069 with REAR AXLE 749.323/336/345/346

with HDB air suspension

Test specifications for trailer axle

Number

Designation

Trailer axle 749.30

Trailer axle 749.320/321/322/323/324/325

BE35.50-N-1001-01A

Angular alignment of trailer axle

mm/m

2

2

Test specifications for trailer axle

Number

Designation

Trailer axle 749.330/334/335/336/337

Trailer axle 749.340/345/346/347/348/349/360/361/368/369

BE35.50-N-1001-01A

Angular alignment of trailer axle

mm/m

2

2

Trailing arms, transverse control arms

Number

Designation

Trailing axle 749.300/301/305./

Trailer axle 749.306/307/320/321/322/330/335/337/340/347/348 with air suspensionHT250

BA35.15-N-1006-02A

Thrust disk nut of retaining bracket bolted connection

Stage 1

Nm

400

400

Stage 2

°

180

180

Trailing arms, transverse control arms

Number

Designation

Trailer axle 749.323/336/345/346 with air suspension HDB

Trailer axle 749.306/307/320/323/330/336/345/346 with air suspension DLS

BA35.15-N-1006-02A

Thrust disk nut of retaining bracket bolted connection

Stage 1

Nm

400

–

Stage 2

°

180

–

Adjust driveline angle

1

Replace pressure plate nut (2) and related bolt.


Only when, instead of the pressure plate nut (2), another nut is installed is or the pressure plate nut (2) and screw/bolt have not been replaced immediately beforehand. Do not yet tighten the pressure plate nut (2).


2

Loosen pressure plate nut (2).


3

Turn the eccentric disk (1) forwards or backwards until the specified angular alignment of the trailer axle is adjusted .


Align trailer axle to kingpin. Do not use a tape measure.


4

Tighten pressure plate nut (2) to specified tightening torque .


Before tightening the pressure plate nut (2) set the normal driving level.
This prevents damage to the bushings.


Counterhold bolt if necessary. The threaded connection should be checked annually with the specified test torque. On vehicles with arduous operating conditions the check should be carried out at correspondingly shorter time intervals.

G35.20-3104-01