ar3520p0109w

Remove/install track rod

Typ ar · téma 35.20 · verze 0100 · 2011-03-02

Platí pro: MODEL 172

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 2 Podvozek › 35 Zadní náprava › 35.20 Vedení kola, náboj — Řada 172

EinPAS 22 Řízení › 22.20 Přídavné řízení › 22.20.40 Páka řízení/řídicí tyč/spojovací tyč řízení/tlumič — Řada 172

AR35.20-P-0109W

Remove/install track rod

17.2.11

MODEL 172

Remove/install track rod

P35.20-2261-06

1 Lever (with code (615) Bi-xenon headlamp unit with integrated curve illumination or
code (621) Intelligent Light System (left-hand traffic) or
code (622) Intelligent Light System (right-hand traffic) or code (483) ADVANCED AGILITY package)

2 Clip (with code (615) Bi-xenon headlamp unit with integrated curve illumination or
code (621) Intelligent Light System (left-hand traffic) or
code (622) Intelligent Light System (right-hand traffic) or code (483) ADVANCED AGILITY package)

3 Eccentric disk

4 Tie rod

4b Rubber bushing

Remove/install

Danger!

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.

AS00.00-Z-0010-01A

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

While working on the rear axle care must be taken to ensure that the surfaces of aluminum components do not get any scratches, cracks and notches. Otherwise the service life of the of the parts will be reduced.

1

Detach left and right rear wheel

AP40.10-P-4050V

2

Unclip lever (1) of left rear level sensor from clip (2) of left tie rod (4)

When removing the left tie rod (4) on vehicles with code (615) Bi-xenon headlamp unit with integrated curve illumination or
with code (621) Intelligent Light System (left-hand traffic) or
with code (622) Intelligent Light System (right-hand traffic) or

with code (483) ADVANCED AGILITY package.

3

Unclip lever (1) of right rear level sensor from clip (2) of right tie rod (4)

When removing the right tie rod (4) on vehicles with code (483) ADVANCED AGILITY package.

4

Detach tie rod (4) from wheel carrier

Do not damage the rubber boot of the tie rod (4).

Installation: Clean grease off the ball head bolt as well as beveled seat in the wheel carrier. Press ball head bolt firmly into the cone and if necessary hold securely using an Allen wrench.

*BA35.20-P-1001-04I

Thrust piece

*171589003400

Puller

*221589003300

5

Mark eccentric disk (3) of tie rod (4) relative to rear axle carrier (arrow)

Installation: Observe marking.

6

Detach tie rod (4) from rear axle carrier

*BA35.20-P-1002-04I

7

Install in the reverse order

Installation: Only tighten bolts and nuts of the chassis components in the curb condition.

8

Perform wheel alignment check

AR40.20-P-0200EW

Tie rod

Number

Designation

Model
172

BA35.20-P-1001-04I

Self-locking nut, tie rod at wheel carrier

Stage 1

Nm

30

Stage 2

°

90

BA35.20-P-1002-04I

Self-locking nut, track rod to rear axle carrier

Stage 1

Nm

70

Stage 2

°

-

Remove/install track rod
Remove/install track rod

221 589 00 33 00

Puller

Thrust piece

171 589 00 34 00

Odkazované dokumenty