ar3520b030101d
Adjust wheel bearing play on rear wheel hub
Typ ar · téma 35.20 · verze 0104 · 2020-09-04
Platí pro: Rear axle 742.8 in model 382 Rear axle 745.9 in model 382 Rear axle 746.875 in model 382
Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.
Zařazení
Funkční skupina 2 Podvozek › 35 Zadní náprava › 35.20 Vedení kola, náboj — Řada 382
EinPAS 17 Hnací ústrojí/náprava › 17.51 Zadní náprava › 17.51.41 Těhlice zadního kola / čep nápravy / náboj kola / ložisko kola — Řada 382
EinPAS 17 Hnací ústrojí/náprava › 17.52 Přídavná náprava › 17.52.42 Těhlice zadního kola / čep nápravy / náboj kola / ložisko kola — Řada 382
Platí také pro motory/převodovky: 742 8**, 745 9**, 746 875
AR35.20-B-0301-01D
| Adjust wheel bearing play on rear wheel hub
|
|
|
Rear axle
| 742.8 in model 382
|
Rear axle
| 745.9 in model 382
|
Rear axle
| 746.875 in model 382
|
Number
| Designation
|
| Rear axle 742.8
| Rear axle 745.0/5/9
|
BE35.20-B-1001-02A
| End play of wheel hub bearings
| mm
| 0,02...0,04
| 0,02...0,04
|
Number
| Designation
|
| Rear axle 746.8/9
|
BE35.20-B-1001-02A
| End play of wheel hub bearings
| mm
| 0,02...0,04
|
Number
| Designation
|
|
| Rear axle 742.8 (except 742.82), 745.5, 745.9, 746.875
|
BA35.20-B-1001-06B
| Inner slotted nut
| First stage
| Nm
| 350
|
|
|
| Second stage
| °
| 110
|
Number
| Designation
|
|
| Rear axle 742.8 (except 742.82), 745.5, 745.9, 746.875
|
BA35.20-B-1002-06B
| Outer grooved nut
| M52
| Nm
| -
|
|
|
| M62
| Nm
| -
|
|
|
| M75
| Nm
| -
|
|
|
| M80
| Nm
| -
|
|
|
| M83
| Nm
| 400
|
|
|
| M85
| Nm
| 400
|
Check
1
| Install the dial indicator holder together with the dial indicator with a little pre-load.
|
2
| Set the dial indicator to "zero".
|
3
| Determine the axial play of the wheel hubs' bearings, moving the wheel hub forward and backward. .
|
4
| Remove the outer slotted nut with the lock plate, and adjust the wheel hub end play
|
|
| If the play value found is incorrect
|
Adjust
5
| Tighten the inner slotted nut with the respective claw wrench to the specified tightening torque. .
|
|
| Strike the wheel hub with a rubber hammer during the tightening procedure of the inner slotted nut for seating the bearings.
|
6
| Loosen the inner slotted nut in the specified "A" angle.
|
7
| Install the dial indicator holder together with the dial indicator.
|
8
| Set the dial indicator to "zero".
|
9
| Determine the axial play of the wheel hubs' bearings, moving the wheel hub forward and backward.
|
10
| Install a new lock plate, and tighten the outer slotted nut to the specified tightening torque using the respective claw wrench. .
|
11
| Lock the lock plate by folding the tabs over the two slotted nuts, inner and outer.
|
