Remove/install lower wishbone · ar3320p0510b · Mercedes-Benz WIS

AR33.20-P-0510B

Remove/install lower wishbone

12.9.11

MODEL 170, 202, 208

P33.20-0283-01

P33.20-0275-01

Figures shown model 202

22b Torsion bar mounting bar

22c Nut

044 Puller

044a Thrust piece

P33.20-0268-01

P33.20-0272-01

11 Shock absorber

11k Screw

Nut

19 Transverse control arm bolt

19a Washer

19b Nut

20 Transverse control arm bolt

20a Washer

20b Nut

 	Remove/install
1	Remove front wheel		AP40.10-P-4050Z
2	Remove front springs		AR32.20-P-0200B
3	Detach torsion bar mounting bar (22b)		*BA32.20-P-1001-02C
4	Unscrew nut from supporting joint		*BA33.20-P-1004-01A
5	Screw thrust piece (044a) onto the ball stud of the supporting joint		*140589006300
6	Press supporting joint out of steering knuckle using puller (044)	  Clean conical joint	*202589023300
7	Detach damper (11) from transverse control arm		*BA32.25-P-1003-01B
8	Detach lower control arm from frame floor assembly	 Model 170: Detach lower engine compartment paneling	AR33.10-P-0200-01B
		 Installation: Tighten nuts in ready-to-drive condition.
		 Installation: Install repair bolts. If repair bolts have already been installed, observe installation position and install bolts in the same position again.	AR40.20-P-0322-01B
			*BA33.20-P-1009-01A
		 Observe technical modifications 
		Bearing bracket of lower control arm	BT33.20-P-9308-01B
9	Unscrew nut of supporting joint to transverse control arm		*BA33.20-P-1006-01A
10	Screw thrust piece onto the ball pivot of the supporting joint		*140589006300
11	Using puller, press supporting joint out of lower control arm	  Clean conical joint if necessary	*202589023300
12	Check transverse control arm for bending and corrosion	
13	Install in the reverse order
14	Perform a wheel alignment check	 Tighten nuts in ready-to-drive condition.	AR40.20-P-0200A

 Front axle stabilizer bar

Number	Designation		Model 202	Model 208


BA32.20-P-1001-02C	Self-locking nut for attaching retaining bracket to transverse control arm	Nm	20	20

 Front axle stabilizer bar

Number	Designation		Model 170


BA32.20-P-1001-02C	Self-locking nut for attaching retaining bracket to transverse control arm	Nm	20

 Front axle shock absorber

Number	Designation			Model 170	Model 202	Model 208


BA32.25-P-1003-01B	Self-locking nut, shock absorber to wishbone	–	Nm	55	55	55
		Yellow	Nm	-	-	-
		silver/blue	Nm	-	-	-

 Wheel location, hub

Number	Designation		Model 170	Model 202	Model 208


BA33.20-P-1004-01A	Self-locking nut, supporting joint to steering knuckle	Nm	105	105	105
BA33.20-P-1006-01A	Self-locking nut, supporting joint to lower transverse control arm	Nm	105	105	105
BA33.20-P-1009-01A	Self-locking nut, lower wishbone to frame	Nm	120	120	120

140 589 00 63 00

202 589 02 33 00

Puller

Thrust piece