ar3315p0160p

Remove/install torque strut at front axle

Typ ar · téma 33.15 · verze 0405 · 2014-02-20

Platí pro: MODEL 203 (except 203.081/084/087/092/281/284/287/292) MODEL 209 without CODE P98 (Black Series)

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 2 Podvozek › 33 Přední náprava › 33.15 Rameno nápravy — Řada 203 (modely 004, 006, 007, 008, 016, 018, 020, 035, 040, 042, 043, 045, 046, 052, 054, 056, 061, 064, 065, 076, 204, 206, 207, 208, 216, 218, 220, 235, 240, 242, 243, 245, 246, 252, 254, 256, 261, 264, 265, 276, 706, 707, 708, 718, 730, 731, 735, 740, 741, 742, 743, 745, 746, 747, 752, 756, 764) · Řada 209

EinPAS 17 Hnací ústrojí/náprava › 17.50 Přední náprava › 17.50.41 Příčné rameno/rameno/stabilizátor — Řada 203 (modely 004, 006, 007, 008, 016, 018, 020, 035, 040, 042, 043, 045, 046, 052, 054, 056, 061, 064, 065, 076, 204, 206, 207, 208, 216, 218, 220, 235, 240, 242, 243, 245, 246, 252, 254, 256, 261, 264, 265, 276, 706, 707, 708, 718, 730, 731, 735, 740, 741, 742, 743, 745, 746, 747, 752, 756, 764) · Řada 209

AR33.15-P-0160P

Remove/install torque strut at front axle

10.02.2014

MODEL

203 (except 203.081/084/087/092/281/284/287/292)

MODEL

209

without CODE P98 (Black Series)

Remove/install torque strut at front axle

P33.15-2037-09

1

Nut

5

Bolts, wheel carrier at the bottom

9

Screw

2

Ball stud

6

Nut

10

Strut rod

3

Nut, wheel carrier at the top

7

Link rod

11

Front axle carrier

4

Screw

8

Nut

12

Elastomer bearing

Remove/install torque strut at front axle

13

Bolts

14

Nuts

P32.20-2102-01

Danger !

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

Evaluation of elastomer bearings

AH00.10-P-0001-01A

Remove/install

1

Raise vehicle

Lift/jack up vehicle

AR00.60-P-1000P

2

Detach complete wheel

Remove/install wheels, rotate if necessary

AP40.10-P-4050Z

3

Unscrew nut (1)

Self-locking nut, strut rod to steering knuckle

*BA33.20-P-1004-01E

4

Press ball head bolt (2) out of the wheel carrier

Puller

*171589003300

Thrust piece

*171589003400

5

Unscrew nut of upper wheel carrier (3)

6

Take out bolt (4)

MODEL 203 (except 203.081/084/087/092/281/284/287/292)

*BA32.25-P-1010-01B

MODEL 209
without CODE P98 (Black Series)

*BA32.25-P-1002-01E

7

Remove bolts from lower wheel carrier (5)

MODEL 203 (except 203.081/084/087/092/281/284/287/292)

*BA32.25-P-1008-01B

MODEL 209
without CODE P98 (Black Series)

*BA32.25-P-1003-01E

8

Unscrew nut (6)

Self-locking nut, connecting rod to spring strut

*BA32.20-P-1004-02B

9

Remove link rod (7)

Self-locking nut, connecting rod to torsion bar

*BA32.20-P-1002-02B

10

Detach torsion bar on front axle carrier (11); to do this, unscrew bolts (13) on torsion bar

Right and left side.

Bolt, torsion bar retaining bracket to front axle carrier

*BA32.20-P-1009-02B

11

Remove headlamp range adjustment sensor. To do this, remove nuts (14)

MODEL 203 (except 203.081/084/087/092/281/284/287/292)
with CODE 614 (Bi-xenon headlamp unit)
MODEL 209
with CODE 614 (Bi-xenon headlamp unit)
without CODE P98 (Black Series)

12

Unscrew nut (8)

Self-locking nut, torque strut to front axle carrier

*BA33.20-P-1007-01E

13

Remove bolt (9)

14

Remove strut rod (10)

Pry out of front axle carrier (11) using assembly lever.

Installation: Screw on nut (8) up to contact surface, but do not yet tighten so that the elastomer bearing (12) of the strut rod (10) can still turn when rocking vehicle to settle suspension. Only tighten nut (8) in the ready-to-drive condition.

Check

15

Inspect radius rod (10) for visible signs of damage or deformation.

16

Check rubber boots on elastomer bearing (12) for damage

The rubber boots should be retrofitted to protect the elastomer bearings (12).

If necessary, replace or retrofit rubber boots:

Remove/install rubber boots on rubber mount

AR33.15-P-0160-03T

17

Check elastomer bearing (12)


If the elastomer bearings (12) are cracked or brittle, then either the elastomer bearing (12) or the complete strut rod (10) has to be replaced.
Otherwise the chassis geometry will be faulty.

MODEL 203.### (except 203.081/084/087/092/281/284/287/292) #A up to 033999
MODEL 203.### (except 203.081/084/087/092/281/284/287/292) #F up to 018699
MODEL 203.### (except 203.081/084/087/092/281/284/287/292) #R up to 000999
The strut rod (10) must be replaced if any damage is determined on the elastomer bearing (12).

Extraction and insertion tool

*220589064300

Replace elastomer bearings (12) individually:

MODEL 203.### (except 203.081/084/087/092/281/284/287/292) #A as of 034000
MODEL 203.### (except 203.081/084/087/092/281/284/287/292) #F as of 018700
MODEL 203.### (except 203.081/084/087/092/281/284/287/292) #R as of 001000
MODEL 209
without CODE P98 (Black Series)

Press torque strut rubber bushing in/out

AR33.15-P-0160-02P

18

Install in the reverse order

Front axle torsion bar

Number

Designation

MODEL 203 (except /020/08/220/28/29)

MODEL 203.020/220

BA32.20-P-1002-02B

Self-locking nut, connecting rod to torsion bar

M10

Nm

60

55

M101.5

Nm

–

–

M121.5

Nm

–

M141.5

Nm

–

–

Front axle torsion bar

Number

Designation

MODEL 209

BA32.20-P-1002-02B

Self-locking nut, connecting rod to torsion bar

M10

Nm

–

M101.5

Nm

55

M121.5

Nm

100

M141.5

Nm

–

Front axle torsion bar

Number

Designation

MODEL 203 (except /020/08/220/28/29)

MODEL 203.020/220

BA32.20-P-1004-02B

Self-locking nut, connecting rod to spring strut

M10

Nm

60

–

M101.5

Nm

–

–

M121.5

Nm

–

–

M12

Nm

–

80

Front axle torsion bar

Number

Designation

MODEL 209

BA32.20-P-1004-02B

Self-locking nut, connecting rod to spring strut

M10

Nm

–

M101.5

Nm

55

M121.5

Nm

100

M12

Nm

–

Front axle torsion bar

Number

Designation

MODEL 203 (except /020/08/220/28/29)

MODEL 203.020/220

BA32.20-P-1009-02B

Bolt, torsion bar retaining bracket to front axle carrier

Stage 1

Nm

40

30

Stage 2

°

–

–

Front axle torsion bar

Number

Designation

MODEL 209

BA32.20-P-1009-02B

Bolt, torsion bar retaining bracket to front axle carrier

Stage 1

Nm

40

Stage 2

°

–

Front axle shock absorber

Number

Designation

MODEL 209 except CODEP98

BA32.25-P-1002-01E

Self-locking nut, suspension strut to steering knuckle at top

Stage 1

Nm

100

Stage 2

°

90

Front axle shock absorber

Number

Designation

MODEL 209 except CODEP98

BA32.25-P-1003-01E

Self-locking bolt, suspension strut to steering knuckle at bottom

Nm

110

Front axle shock absorber

Number

Designation

MODEL 203 except 4MATIC

BA32.25-P-1008-01B

Self-locking bolt, suspension strut to steering knuckle at bottom

Nm

110

Front axle shock absorber

Number

Designation

MODEL 203 except 4MATIC

BA32.25-P-1010-01B

Self-locking nut, suspension strut to steering knuckle at top

Stage 1

Nm

100

Stage 2

°

90

Wheel control, hub

Number

Designation

MODEL 203

MODEL 209

BA33.20-P-1004-01E

Self-locking nut, strut rod to steering knuckle

Stage 1

Nm

50

50

Stage 2

°

60

60

Wheel control, hub

Number

Designation

MODEL 203

MODEL 209

BA33.20-P-1007-01E

Self-locking nut, torque strut to front axle carrier

Stage 1

Nm

80

80

Stage 2

°

120

120

Remove/install torque strut at front axle
Remove/install torque strut at front axle
Remove/install torque strut at front axle

220 589 06 43 00

Extraction and insertion tool

171 589 00 34 00

Thrust piece

171 589 00 33 00

Puller

Odkazované dokumenty