ar2750d078011a

Insert/measure disk pack B3

Typ ar · téma 27.50 · verze 0201 · 2007-09-10

Platí pro: TRANSMISSION 722.681 in MODEL 902.6, 903.6, 904.6, 905.6 TRANSMISSION 722.681 in MODEL WD1, WD2, WD3, WD6, WD7, XD1, XD2, XD3, XD4, XD5, XD6, XD7, YD1, YD2, YD3, YD4, YD5, YD6, YD7

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 2 Podvozek › 27 Automatická převodovka › 27.50 Soukolí — Řada 902 (modely 6**) · Řada 903 (modely 6**) · Řada 904 (modely 6**) · Řada 905 (modely 6**)

EinPAS 17 Hnací ústrojí/náprava › 17.20 Převodovka › 17.20.54 Lamelová brzda/lamelová spojka — Řada 902 (modely 6**) · Řada 903 (modely 6**) · Řada 904 (modely 6**) · Řada 905 (modely 6**)

Platí také pro motory/převodovky: 722 681

AR27.50-D-0780-11A

Insert/measure disk pack B3

Automatic transmission fluids
(ATF, Sheet 236.10)

Sheet 236.10

BB00.40-P-0236-10A

Modification notes

24.9.03

Value changed from 2.00...2.40 Nm to 1.00...1.40 mm

Value in row 1003 on transmission 722.681 up to trans. no. 3947439 changed

*BE27.51-N-1003-01A

24.9.03

Value changed from 2.00...2.40 Nm to 1.00...1.40 mm

Value in row 1003 on transmission 722.681 as of trans. no. 3947439 changed

*BE27.51-N-1003-01A

Test and adjustment values

Number

Designation

Transmis-sion 722.681 up to trans. no. 3947439

Transmis-sion 722.681 as of trans. no. 3947440

BE27.51-N-1003-01A

Disk play of multi-disk brake B3

mm

1,00 to 1,40

1,00 to 1,40

Insert/measure disk pack B3

D27.50-1112-01

1 Put together externally toothed plates (2, 4) and internally toothed plates (3) in the sequence shown and insert individually.

Place new externally toothed plates and internally toothed plates in ATF oil 1 h before installation.

2 Install circlip (1).

Both ends of the circlip (1) must be seated on a toothing wedge.

Design of multidisk brake

1 Circlip

2 Externally toothed disk (6.5 mm)

3 Internally toothed plates

4 Externally toothed plates (1.8 mm)

5 Disk spring

6 Piston B3 (external plate carrier B2)

L Toothed plate play

Insert/measure disk pack B3

D27.50-1113-01

3 Place transmission housing with the outward side downwards.

4 Pull up clutch pack with both hands on the inside and allow to fall down.

To measure the toothed plate play (L) the circlip (1) must abut with the upper contact surface of the groove.

5 Using a feeler gauge, check the toothed plate play (L) at three points between the circlip (1) and externally toothed plate (2).

If necessary, adjust the toothed plate play (L) by installing a circlip (1) of corresponding thickness.

Odkazované dokumenty