ar2520b010001a

Detach/attach line

Typ ar · téma 25.20 · verze 0102 · 2020-08-14

Platí pro: Model 368, 685.282/284/289/290 with transmission 712.622/631 Model 382 with engine 906.918/933/974/975/977/983/988/994/998, 926.910/926/999 Model 384 with transmission 712, 713, 715, 718 Model 384 with transmission 712, 713, 715 Model 384 with transmission 712, 713 Model 688 with engine 904.924/957 Model 693 with engine 904.925

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 2 Podvozek › 25 Spojka › 25.20 Ovládání spojky — Řada 368 · Řada 382 · Řada 384 · Řada 685 (modely 282, 284, 289, 290) · Řada 688 · Řada 693 · Řada 904 (modely 924, 925, 957) · Řada 906 (modely 918, 933, 974, 975, 977, 983, 988, 994, 998)

EinPAS 17 Hnací ústrojí/náprava › 17.15 Spojka › 17.15.13 Potrubí/hadice/ventil — Řada 368 · Řada 382 · Řada 384 · Řada 685 (modely 282, 284, 289, 290) · Řada 688 · Řada 693 · Řada 904 (modely 924, 925, 957) · Řada 906 (modely 918, 933, 974, 975, 977, 983, 988, 994, 998)

Platí také pro motory/převodovky: 712 ***, 712 622, 712 631, 713 ***, 715 ***, 718 ***, 926 910, 926 926, 926 999

AR25.20-B-0100-01A

Detach/attach line

Model

368, 685.282/284/289/290 with transmission 712.622/631

Model

382 with engine 906.918/933/974/975/977/983/988/994/998, 926.910/926/999

Model

384 with transmission 712, 713, 715, 718

Model

384 with transmission 712, 713, 715

Model

384 with transmission 712, 713

Model

688 with engine 904.924/957

Model

693 with engine 904.925

Repair materials

Number

Designation

Order number

BR00.45-Z-1108-06A

Grease, DBL 6812.00

Klueber Lubrification

BR00.45-Z-1110-06A

Brake fluid, DB supply specification 7760.30 (DOT 4)

Use corresponding commercially available repair materials.

Detach/attach line

1

Remove the bellows protector (6), the snap ring (5), the complete piston (4), the spring (3) and the connection ring.



2

Wash hydraulic master cylinder inner section with hydrated alcohol (pharmacy supply). If there are any signs of oxidation use a fine steel sponge. If oxidation cannot be eliminated, replace the complete hydraulic cylinder.



3

With cylinders (1) in good condition, perfectly clean and lubricated with specified brake fluid, install the new components that correspond to the repair kit in order:
- Connection snap ring (2).
- Return spring (3) (observe the correct position).
- Complete piston (4) with gaskets.
- Install new snap ring (5).



4

Check free piston (4) movement within cylinder (1).



5

Use long-lasting grease to lubricate contact area between rod and piston.



6

Fit the new bellows protector.



7

If the cylinder is not used immediately, cover the connection ports and the snap ring with appropriate plastic plugs.



8

Install the plastic identification clamp that comes with the cylinder.


Hydraulic master cylinder repair kit replacement shown here is applicable to all vehicles of the series, however, cylinder diameter and piston stroke vary according to vehicle cargo capacity, as indicated on the plastic identification clamp that comes with the cylinder.

Cylinder components must only be washed with hydrated alcohol (pharmacy supply). Oil-derived products, such as gasoline, kerosene or Diesel fuel will damage rubber components.

B25.20-0003-10