Remove/install engine mount

AR22.10-P-1100AV

7.11.08

ENGINE 112.940 in MODELS 208.365 /465

ENGINE 112.910 in MODELS 202.026 /086

ENGINE 112.920 in MODELS 202.029 /089

ENGINE 113.944 in MODELS 202.033 /093

P22.10-2005-12

1 Engine mount

2 Shields

3, 4 Bolt

P46.10-0203-01

10 Track rods

11 Drag link

23 Steering gear

26 Relay lever

46 Steering damper

 	Remove/install
1	Remove engine cover or air filter	On model 202.033/093 the air filter is integrated in the engine trim panel. Remove engine cover or air filter by pulling it vertically up and off cylinder head covers.
2	Disconnect/connect battery ground line	 Only necessary if the right engine mount is removed. Installation: After connecting, read fault memory, encode radio and normalize power windows. Vehicles with stationary heater: adjust time display on stationary heater.	AR54.10-P-0003A
3	Put on engine carrier arm		AR33.10-P-0100-01AV
4	Unscrew bolts (4) connecting engine mount (1) to front axle carrier		*BA22.10-P-1001-01L
5	Unbolt steering damper (46) at drag link (11)		*BA46.40-P-1001-03A
6	Unscrew nuts of drag link (11) at Pitman arm and at relay lever (26)	 Counterhold ball studs, if necessary, with hexagon socket wrench. Installation:  Replace self-locking nuts.
			*BA46.40-P-1001-04A
7	Use puller to press drag link (11) off at pitman arm and at relay lever (26) and detach	 Install thrust piece at relevant joint. Installation: Clean tapers free of grease and press ball joints firmly into the drag links. Inspect play of joint, rubber boot, replace drag link, if necessary.
		Remove drag link.	AR46.40-P-0100C
			*129589106300
			*202589013300
8	Remove shield at relay lever (26)
9	Unscrew bolts (3) connecting engine mount (1) to engine support		*BA22.10-P-1004-01L
			*112589001600
10	Raise engine at front lifting eye	 Ensure that rear of engine does not touch the body! Do not over-tension coolant hoses and ground cable (W11/4 engine support left  front axle carrier)!
11	Remove shields (2)	Installation: The recesses in shields must be located in the anti-twist locks of the engine supports.
12	Remove engine mounts (1)	Installation:  The anti-twist locks (arrows) at engine mounts (1) must fit in retaining grooves (arrows) of the engine supports.
		Installation:  On model 202.033/093 (AMG) harder engine mounts are fitted than in the standard vehicle; pay attention to this when replacing engine mounts!
	Environmental protection regulations for disposal of engine mounts	Dispose engine mounts into mixed scrap.
13	Install in the reverse order
14	Read out fault memory and erase	 Only necessary if the right engine mount is removed.
		Stored faults which can result from cables being disconnected or from simulation during removal and installation or test work, have to be processed and erased in the fault memories after completing the work.
		Diagnosis Manual Volume 2, Index 0: Connecting and using test equipment

 Engine mounts, engine supports

Number	Designation		Engines 112.910/920, 113.944 in models 202.026/029/033/086/089/093	Engine 112.940, 113.943/984 in model 208.365/ 370/374/465/470


BA22.10-P-1001-01L	Bolt, front engine mounts to front axle carrier	Nm	35	35
BA22.10-P-1004-01L	Bolt, front engine mount to engine support	Nm	55	55

 Steering damper

Number	Designation		Model 202	Model 208


BA46.40-P-1001-03A	Steering damper to drag link	Nm	40	40

 Drag link

Number	Designation			Model 202	Model 208


BA46.40-P-1001-04A	Self-locking nuts of drag link	Stage 1	Nm	50	50
		Stage 2	°	-	-

129 589 10 63 00

Connecting piece

Thrust piece

Puller

202 589 01 33 00

112 589 00 16 00

Odkazované dokumenty